Synthesis of porous microspheres composed of graphitized carbon@amorphous silicon/carbon layers as high performance anode materials for Li-ion batteries

Zailei Zhang,Yanhong Wang,Wenfeng Ren,Ziyi Zhong,Fabing Su

DOI: https://doi.org/10.1039/c4ra09868d

2014-01-01

RSC Adv.

Abstract:Amorphous silicon/carbon (Si/C) layers coated on graphitized carbon black (GCB) particles in porous microspheres (PMs) exhibited an improved electrochemical performance.

What problem does this paper attempt to address?

In Situ Synthesis of Carbon Doped Porous Silicon Nanocomposites As High-Performance Anodes for Lithium-Ion Batteries.

Yifan Chen,Liang Bao,Ning Du,Tao Yang,Qinan Mao,Xiaoxiao Lu,Yangfan Lin,Zhenguo Ji

DOI: https://doi.org/10.1088/1361-6528/aaeb04

IF: 3.5

2018-01-01

Nanotechnology

Abstract:We demonstrate the in situ synthesis of carbon doped porous silicon (Si/C) nanocomposites by a simple thermal displacement process between Mg2Si and inorganic gas CO2 in one-step. Via the decomposition of Mg2Si, the reduction process occurred between Mg and CO2, leading the uniform doping of many distributed tiny carbon nanoparticles into Si. Meanwhile, the porous structure was formed after an acid treatment. When worked as anodes for lithium-ion batteries, the as-prepared s-porous Si/C nanocomposites exhibited good cycling stability and high-rate capability, which were superior to the porous Si and porous Si/C nanocomposites. It was revealed that the enhanced electrochemical properties could be ascribed to the novel porous structure and doped carbon nanoparticles that can buffer the volume expansion, as well as enhance the electronic conductivity of Si. The reaction mechanism was well investigated by studying the influence of reaction temperature and raw Mg2Si particle size on the morphology and component of the porous Si/C nanocomposites.
Preparation of porous silicon/carbon microspheres as high performance anode materials for lithium ion batteries

Wenfeng Ren,Zailei Zhang,Yanhong Wang,Qiangqiang Tan,Ziyi Zhong,Fabing Su

DOI: https://doi.org/10.1039/c4ta07093c

IF: 11.9

2015-01-01

Journal of Materials Chemistry A

Abstract:Porous silicon/carbon microspheres assembled with fine carbon particles and silicon nanoparticles show improved electrochemical performance as anode materials for lithium ion batteries.

materials science, multidisciplinary,chemistry, physical,energy & fuels
Novel Design of Uniform Si@graphite@C Composite As High-Performance Li-ion Battery Anodes

Sijia Zhu,Yangfan Lin,Zhilin Yan,Jingwei Jiang,Deren Yang,Ning Du

DOI: https://doi.org/10.1016/j.electacta.2021.138092

IF: 6.6

2021-01-01

Electrochimica Acta

Abstract:We design a novel Si@graphite@C composite via the pretreatment of graphite, subsequent deposition of Si nanoparticles via chemical vapor deposition, and finally the coating of carbon layer. The enlarged macropores of graphite can accommodate more loading of Si nanoparticles and the use of monosilane gas as source can bring the uniform deposition of Si nanoparticles in the whole graphite microparticles. The Si@graphite@C composite has good electrical conductivity and can well accommodate the volume change during the charge/discharge process, thus result in a good electrochemical performance. The relationship between pore size distribution, Si particles distribution and electrode performance is also investigated. (c) 2021 Published by Elsevier Ltd.
Simple Synthesis of SiGe@C Porous Microparticles As High-Rate Anode Materials for Lithium-Ion Batteries

Yaguang Zhang,Ning Du,Chengmao Xiao,Shali Wu,Yifan Chen,Yangfan Lin,Jinwei Jiang,Yuanhong He,Deren Yang

DOI: https://doi.org/10.1039/c7ra04364c

IF: 4.036

2017-01-01

RSC Advances

Abstract:We synthesize the PoSiGe@C via the decomposition of Mg2Si/Mg2Ge composites, acid pickling and subsequent carbon coating processes, which show excellent cycling and rate performance as anode materials for lithium-ion batteries.
Wet-chemical Synthesized MCMB@Si@C Microspheres for High-Performance Lithium-Ion Battery Anodes.

Yangfan Lin,Yifan Chen,Yaguang Zhan,Jingwei Jiang,Yuanhong He,Yu Lei,Ning Du,Deren Yang

DOI: https://doi.org/10.1039/c8cc04797a

IF: 4.9

2018-01-01

Chemical Communications

Abstract:MCMB@Si@C microspheres, in which silicon nanoparticles were closely connected with mesocarbon microbeads (MCMBs) through strong chemical bonds, were synthesized as high-performance Li-ion battery anodes for the first time. Furthermore, the different surface functional groups, as interconnecting species, and their effects on the anode performance were characterized in detail.
C porous microparticles as high-rate anode materials for lithium-ion batteries

Yaguang Zhang,Ning Du,Chengmao Xiao,Shali Wu,Yifan Chen,Yangfan Lin,Jinwei Jiang,Yuanhong He,Deren Yang

2017-01-01

Abstract:We report the synthesis of SiGe@C porous microparticles (PoSiGe@C) via the decomposition of Mg2Si/ Mg2Ge composites, acid pickling and subsequent carbon coating processes, respectively. The content of Ge can be tuned by the initial ratio of Mg2Si and Mg2Ge in the composite. The as-synthesized PoSiGe@C has been used as the anode material of lithium-ion batteries, which shows an enhanced cyclic and rate performance compared to bare Si, PoSiGe as well as PoSi@C porous microparticles. Briefly, the PoSiGe@C delivers a good cycling stability with 70% capacity retention after 400 cycles and only 0.075% capacity loss per cycle at the current density of 0.8 A g . Furthermore, super rate capability is also expressed by the PoSiGe@C. The unique porous structure, and synergistic effect of Si and Ge, may lead to the inherent high lithium-ion diffusivity and electrical conductivity of Ge, and good volume alleviation, which results in the good electrochemical performance.
Nano-Si/C microsphere with hollow double spherical interlayer and submicron porous structure to enhance performance for lithium-ion battery anode

Hedong Chen,Shenggong He,Xianhua Hou,Shaofeng Wang,Fuming Chen,Haiqing Qin,Yingchun Xia,Guofu Zhou

DOI: https://doi.org/10.1016/j.electacta.2019.04.170

IF: 6.6

2019-07-01

Electrochimica Acta

Abstract:Silicon (Si) applied for lithium-ion battery anode is of immense prospect due to high theoretical capacity, non-toxic, abundant reserves and low-cost. But the electrode materials, maintaining stable structure during repeated discharge/charge processes, need to be explored, which can realize the long-life. To address this problem, we utilized hollow porous pollen carbon microsphere derived from biomass as hard template to accommodate nano-Si. The hollow porous carbon@nano-Si@graphene sheets (HPC@nano-Si@GS) microspheres with hollow double spherical interlayer and submicron porous structure have been successfully synthesized via a simple and green environment-protecting wet-chemical method. We decorate nano-Si with silane coupling agent which can bind hollow porous pollen and graphene oxide, realizing the strong fixation and protection of nano-Si. Furthermore, the surface submicron mesh pores and HPC microsphere provide enough buffer space to cushion the huge volume expansion for nano-Si, enhancing the cyclic stability. Finally, graphene wrapping on the surface of HPC@nano-Si@GS microspheres can protect nano-Si very well, further stabilizing the composite structure. Nano-Si particles were accommodated in the HPC microsphere with submicron pores and then coated by wrinkled graphene sheets, to form the strong structure with hollow double spherical interlayer. A series of electrochemical tests indicate that prepared HPC@nano-Si@GS microspheres with hollow porous carbon structure exhibit outstanding electrochemical properties.

electrochemistry
Rational-design micro-nanostructure of porous carbon film/silicon nanowire/graphite microsphere composites for high-performance lithium-ion batteries

Bei Liu,Peng Huang,Qi Zhang,Qizhong Huang,Zhiyong Xie

DOI: https://doi.org/10.1007/s10853-020-04869-z

IF: 4.5

2020-06-02

Journal of Materials Science

Abstract:Silicon-based anodes are promising anode materials for lithium-ion batteries. However, during the charge–discharge processes, the huge volume change of silicon leads to the repeated formation of solid-electrolyte interphase layer, structure fracture and loss of electric contact, which seriously limits their practical applications. In this paper, a rational design combining graphite microsphere, silicon nanowire and porous carbon film is established, forming a micro-nanostructure that can effectively solve the above issues. Employing chemical vapor deposition method, silicon nanowire and polypyrrole are successively in situ synthesized on the graphite surface. After carbonizing the deposited composites, a porous carbon film and a silicon carbide layer locating between silicon and carbon film are obtained. It establishes a novel microstructure that possesses a strong bonding strength among interfaces of carbon film/silicon and silicon/graphite. Therefore, the porous carbon film/silicon nanowire/graphite microsphere composites anode exhibits a high capacity of 530 mA h g−1 at a current density of 0.2 C after 100 cycles. Significantly, the prepared composites anode could satisfy the practical application because their initial coulomb efficiency can reach to 80%.Graphic abstract

materials science, multidisciplinary
3-Aminopropyltriethoxysilane-assisted Si@Sio2/Cnts Hybrid Microspheres As Superior Anode Materials for Li-Ion Batteries

Jiyun Wang,Xianhua Hou,Miao Zhang,Yana Li,Yuping Wu,Xiang Liu,Shejun Hu

DOI: https://doi.org/10.1007/s12633-015-9398-0

IF: 3.4

2016-01-01

Silicon

Abstract:A silicon based composite (Si@SiO2/CNTs) with outstanding electrochemistry performance has been easily synthesized using a spray drying method; The composite microsphere is mainly made up of carbon nanotubes and the prepared nano silicon particles. With the help of a silane coupling agent, carbon nanotubes tightly intertwined with nano silicon particles and formed microspheres together. On the surface of the prepared nano silicon particles, a layer of oxide film plays a role as a barrier to reduce the rupture of the particles during the lithium intercalation/extraction process. In addition, the added twisted carbon nanotubes can help to maintain the conductive network, thus stabilizing the electrode working environment during the lithium intercalation/extraction process. As a superior anode material, an initial specific discharge capacity of approximately 2846.9 mAh g−1 with a coulombic efficiency of 86 % and a reversible specific capacity of 2035.9 mAh g−1 after 100 cycles at a constant density of 500 mA g−1 are obtained.
Synthesis of a novel porous silicon microsphere@carbon core-shell composite via in situ MOF coating for lithium ion battery anodes

Kai Wang,Shien Pei,Zhishun He,Liangai Huang,Shasha Zhu,Jianfeng Guo,Haibo Shao,Jianming Wang

DOI: https://doi.org/10.1016/j.cej.2018.09.027

IF: 15.1

2019-01-01

Chemical Engineering Journal

Abstract:A novel porous silicon microsphere@carbon core-shell composite synthesized by using in situ MOF coating manifests enhanced lithium storage performance.
Electrosprayed silicon-embedded porous carbon microspheres as lithium-ion battery anodes with exceptional rate capacities

Liang Gemeng,Qin Xianying,Zou Jinshuo,Luo Laiyan,Wang Yunzhe,Wu Mengyao,Zhu Hua,Chen Guohua,Kang Feiyu,Li Baohua

DOI: https://doi.org/10.1016/j.carbon.2017.11.013

IF: 10.9

2018-01-01

Carbon

Abstract:Silicon-embedded porous carbon microspheres with an exceptional conductive framework for ions and electrons were obtained by electrospraying a mixed polymer solution of polystyrene and polyvinylpyrrolidone, containing silicon nanoparticles, carbon nanotubes and carbon blacks, and subsequent heat treatment. In the composite microspheres, silicon particles were embedded in the porous carbon framework composed of interwoven carbon nanotubes, filled carbon blacks and interconnected amorphous carbon derived from polymers. The cage-like porous carbon microspheres could not only accommodate the volume expansion of silicon but also ensure a robust electrical contact, fast transport for electrons and ions. Therefore, the silicon/carbon anode exhibits a high capacity of 1325 mAh g−1 at 0.2 A g−1 after 60 cycles and superior rate capability with a capacity of 925 mAh g−1 at a large current density of 5 A g−1.
Carbon coated porous hollow silicon microspheres for high‐capacity and durable lithium storage

Yumei Yang,Ruhan He,Dingyue Zhuang,Ran Chen,Qi Li,Liqiang Mai,Liang Zhou

DOI: https://doi.org/10.1002/cnma.202300265

IF: 3.82

2023-06-28

ChemNanoMat

Abstract:Silicon‐based materials are promising lithium‐ion battery (LIB) anodes owing to their natural abundance and high capacity. However, their practical application is restricted by the poor electrical conductivity and large volume expansion. Herein, we successfully construct carbon coated porous hollow silicon microspheres (Si‐40@C) as LIB anode materials, which are derived from the acid etching of commercial AlSi alloy with subsequent chemical vapor deposition carbon coating. The porous hollow structure of Si‐40@C buffers the volume variation and promotes the transportation of Li+; the carbon coating enhances the overall conductivity as well as structural stability. The as‐prepared Si‐40@C porous hollow microspheres deliver a high reversible capacity (2029 mAh g‐1 at 0.2 A g‐1), good cyclability (1668 mAh g‐1 after 100 cycles at 0.2 A g‐1), and an ideal rate capability (1200 mAh g‐1 at 10 A g‐1).

materials science, multidisciplinary,nanoscience & nanotechnology,chemistry
Amorphous Carbon Shell on Si Particles Fabricated by Carbonizing of Polyphosphazene and Enhanced Performance As Lithium Ion Battery Anode

Caili Zhang,Angang Song,Peiling Yuan,Qian Wang,Peng Wang,Shilin Zhang,Guoqin Cao,J. H. Hu

DOI: https://doi.org/10.1016/j.matlet.2016.02.034

IF: 3

2016-01-01

Materials Letters

Abstract:A novel strategy was employed to introduce a carbon layer on Si particle to overcome the intrinsic poor electrical conductivity and significant volume change. The carbon layer was fabricated by forming polyphosphazene coating through a facile precipitation polymerization method, followed by carbonization. As a result of formation of core-shell structure, the Si anode exhibited improved cycling stability (740mAh/g remained after 100 cycles) and rate capability (300mAh/g at a rate 2C). In addition, 99% coulombic efficiency was remained after 100 cycles.
Mn0.5Co0.5Fe2O4 nanoparticles highly dispersed in porous carbon microspheres as high performance anode materials in Li-ion batteries

Zailei Zhang,Wenfeng Ren,Yanhong Wang,Jun Yang,Qiangqiang Tan,Ziyi Zhong,Fabing Su

DOI: https://doi.org/10.1039/c4nr00394b

IF: 6.7

2014-06-21

Nanoscale

Abstract:We report the preparation of Mn(0.5)Co(0.5)Fe2O4 (MCFO) nanoparticles highly dispersed within porous carbon microspheres as anodes for Li-ion batteries. In situ growth of MCFO nanoparticles (5-20 nm) on the surface of carbon black (CB) and graphitized carbon black (GCB) nanoparticles was conducted via a hydrothermal method to form MCFO-CB and MCFO-GCB composites, respectively, which were employed as building blocks to assemble MCFO-CB and MCFO-GCB porous microspheres (PM) with a size of 5-30 μm by the spray drying technique using sucrose as a binder, and followed by carbonization in N2 (labeled as MCFO-CB-PM and MCFO-GCB-PM, respectively). Compared with the pure MCFO, MCFO-CB, and MCFO-GCB, both MCFO-CB-PM and MCFO-GCB-PM showed a significantly improved electrochemical performance. This is attributed to their unique porous structure, in which, the abundant pores promote the diffusion of Li-ion and electrolyte solution, the microspherical morphology enhances the electrode-electrolyte contact, and the carbon substrates from CB (and GCB) and sucrose substantially prevent the aggregation of MCFO nanoparticles and buffer the volume change. Particularly, MCFO-GCB-PM exhibits the best rate performance and excellent cycling stability because of the high graphitization degree of GCB. This work opens up an effective route for large scale fabrication of metal oxide/carbon porous microspheres as anode materials for potential applications in the new generation of Li-ion batteries.
Green and facile fabrication of nanoporous silicon@carbon from commercial alloy with high graphitization degree for high-energy lithium-ion batteries

Yuan Tao,Yuan Tian,Yongling An,Chuanliang Wei,Yuan Li,Qikun Zhang,Jinkui Feng

DOI: https://doi.org/10.1016/j.susmat.2020.e00238

IF: 10.681

2021-04-01

Sustainable Materials and Technologies

Abstract:Silicon (Si) is considered as one of the most promising anodes for lithium-ion batteries (LIBs). However, rapid capacity decay caused by huge volume change and low electrical conductivity limit its further development. Herein, uniform porous () from commercial Mg2Si alloy and pitch is synthesized by green vacuum distillation method. During this process, the low boiling-point Mg is evaporated and cycled to form porous Si. Besides, the high-graphitization C layer is obtained because the metallic Mg favors the graphitization degree of C. As a result, the carbon coating layer and unique porous structure can improve electrical conductivity and accommodate volume change of Si anode without destroying solid electrolyte interface. The optimal shows improved lithium storage with stable cyclability and superior rate capability.

energy & fuels,materials science, multidisciplinary,green & sustainable science & technology
Facile preparation of silicon/carbon composite with porous architecture for advanced lithium-ion battery anode

Haofeng Shi,Wenyuan Zhang,Donghua Wang,Jiashuai Wang,Chengdeng Wang,Zhihao Xiong,Fu-Rong Chen,Hailiang Dong,Bingshe Xu,Xiaoqin Yan

DOI: https://doi.org/10.1016/j.jelechem.2023.117427

IF: 4.598

2023-04-10

Journal of Electroanalytical Chemistry

Abstract:Silicon is a potential anode material for Li battery due to its high theoretical specific capacity (4200 mAh g −1 ). However, Si is hampered for practical application in Li-battery due to its enormous volume alternation causing instability. Herein, we demonstrated a novel carbon-coated porous structure (/Si-G) synthesized by uniformly wrapping Si into pitch pyrolytic carbon shells and then in-situ removing the sodium chloride template can overcome the bottleneck. It is worth noting that our process for /Si-G also offers a simple route for cost down and mass production of anode material. The /Si-G anodes exhibit an excellent capacity of 1082.7 mAh g −1 at 0.2 C after 200 cycles. Furthermore, it holds a high capacity retention of 81.9 % after 500 cycles at 0.5 C. We found that /Si-G composite only rises about 41% volumetric expansion during 500 operation cycles. This can effectively avoid direct contact between silicon and electrolyte to form a stable solid electrolyte interphase (SEI) film. Especially, practical application of the /Si-G anode is demonstrated in a full cell pairing with LiNi 0.3 Co 0.3 Mn 0.3 O 2 cathode. The full cell presents great cycle retention of 90.1 % at 0.2 C after 100 cycles and a high energy density (446 Wh kg −1 ).

chemistry, analytical,electrochemistry
Electrochemical Performance Enhancement of Porous Si Lithium-Ion Battery Anode by Integrating with Optimized Carbonaceous Materials

Wentao Yang,Hangjun Ying,Shunlong Zhang,Rongnan Guo,Jianli Wang,Wei-Qiang Han

DOI: https://doi.org/10.1016/j.electacta.2020.135687

IF: 6.6

2020-01-01

Electrochimica Acta

Abstract:Silicon (Si) is regarded as a promising negative material for Li-ion batteries (LIBs), but the poor cyclic performance limits its practical applications. Herein, we used several different carbonaceous materials as carbon sources to form Si/C composites, which was formed by etched Fe-Si alloys followed by mechanical ball mill mixing with carbon. It is found that the artificial graphite as the carbonaceous material can form a well-distributed mixture during the ball milling, and then uniformly coated with amorphous carbon pyrolyzed by the phenolic resin. The pore structure of Si particles can provide rapid diffusion for lithium ions, resulting in improving the electrochemical properties. The well-coated carbon layer promotes the formation of stable SEI layer on the composites surface, which is advantageous for the long cycle performance. The carbonaceous materials (artificial graphite, flake graphite and soft carbon) have remarkable influence on the electrochemical performance of Si/C composites. The silicon/graphiteartificial graphite (Si/C-AG) exhibits the best performance among these three Si/C composites. It delivers a specific capacity of 445 mAh g(-1) at 0.5 A g(-1) with a retention of 94% after 200 cycles. This work would be helpful with choosing suitable carbonaceous materials for the Si/C composites. (C) 2020 Elsevier Ltd. All rights reserved.
High Performance Amorphous-Si@siox/c Composite Anode Materials for Li-ion Batteries Derived from Ball-Milling and in Situ Carbonization

Dingsheng Wang,Mingxia Gao,Hongge Pan,Junhua Wang,Yongfeng Liu

DOI: https://doi.org/10.1016/j.jpowsour.2013.12.128

IF: 9.2

2014-01-01

Journal of Power Sources

Abstract:Amorphous-Si@SiOx/C composites with amorphous Si particles as core and coated with a double layer of SiOx and carbon are prepared by ball-milling crystal micron-sized silicon powders and carbonization of the citric acid intruded in the ball-milled Si. Different ratios of Si to citric acid are used in order to optimize the electrochemical performance. It is found that SiOx exists naturally at the surfaces of raw Si particles and its content increases to ca. 24 wt.% after ball-milling. With an optimized Si to citric acid, weight ratio of 1/2.5, corresponding to 8.4 wt.% C in the composite, a thin carbon layer is coated on the surfaces of a-Si@SiOx particles, moreover, floc-like carbon also forms and connects the carbon coated a-Si@SiOx particles. The composite provides a capacity of 1450 mA h g(-1) after 100 cycles at a current density of 100 mA g(1), and a capacity of 1230 mA h g(-1) after 100 cycles at 500 mA g(1) as anode material for lithium-ion batteries. Effects of ball-milling and the addition of citric acid on the microstructure and electrochemical properties of the composites are revealed and the mechanism of the improvement in electrochemical properties is discussed. (C) 2014 Elsevier B.V. All rights reserved.
Nonfilling carbon coating of porous silicon micrometer-sized particles for high-performance lithium battery anodes.

Zhenda Lu,Nian Liu,Hyun-Wook Lee,Jie Zhao,Weiyang Li,Yuzhang Li,Yi Cui

DOI: https://doi.org/10.1021/nn505410q

IF: 17.1

2015-01-01

ACS Nano

Abstract:Silicon is widely recognized as one of the most promising anode materials for lithium-ion batteries due to its 10 times higher specific capacity than graphite. Unfortunately, the large volume change of Si materials during their lithiation/delithiation process results in severe pulverization, loss of electrical contact, unstable solid-electrolyte interphase (SEI), and eventual capacity fading. Although there has been tremendous progress to overcome these issues through nanoscale materials design, improved volumetric capacity and reduced cost are still needed for practical application. To address these issues, we design a nonfilling carbon-coated porous silicon microparticle (nC-pSiMP). In this structure, porous silicon microparticles (pSiMPs) consist of many interconnected primary silicon nanoparticles; only the outer surface of the pSiMPs was coated with carbon, leaving the interior pore structures unfilled. Nonfilling carbon coating hinders electrolyte penetration into the nC-pSiMPs, minimizes the electrode-electrolyte contact area, and retains the internal pore space for Si expansion. SEI formation is mostly limited to the outside of the microparticles. As a result, the composite structure demonstrates excellent cycling stability with high reversible specific capacity (∼1500 mAh g(-1), 1000 cycles) at the rate of C/4. The nC-pSiMPs contain accurate void space to accommodate Si expansion while not losing packing density, which allows for a high volumetric capacity (∼1000 mAh cm(-3)). The areal capacity can reach over 3 mAh cm(-2) with the mass loading 2.01 mg cm(-2). Moreover, the production of nC-pSiMP is simple and scalable using a low-cost silicon monoxide microparticle starting material.
Monodisperse Porous Silicon Spheres as Anode Materials for Lithium Ion Batteries

Wei Wang,Zachary Favors,Robert Ionescu,Rachel Ye,Hamed Hosseini Bay,Mihrimah Ozkan,Cengiz S. Ozkan

DOI: https://doi.org/10.1038/srep08781

IF: 4.6

2015-01-01

Scientific Reports

Abstract:Highly monodisperse porous silicon nanospheres (MPSSs) are synthesized via a simple and scalable hydrolysis process with subsequent surface-protected magnesiothermic reduction. The spherical nature of the MPSSs allows for a homogenous stress-strain distribution within the structure during lithiation and delithiation, which dramatically improves the electrochemical stability. To fully extract the real performance of the MPSSs, carbon nanotubes (CNTs) were added to enhance the electronic conductivity within the composite electrode structure, which has been verified to be an effective way to improve the rate and cycling performance of anodes based on nano-Si. The Li-ion battery (LIB) anodes based on MPSSs demonstrate a high reversible capacity of 3105 mAh g −1 . In particular, reversible Li storage capacities above 1500 mAh g −1 were maintained after 500 cycles at a high rate of C/2. We believe this innovative approach for synthesizing porous Si-based LIB anode materials by using surface-protected magnesiothermic reduction can be readily applied to other types of SiO x nano/microstructures.

Synthesis of porous microspheres composed of graphitized carbon@amorphous silicon/carbon layers as high performance anode materials for Li-ion batteries

In Situ Synthesis of Carbon Doped Porous Silicon Nanocomposites As High-Performance Anodes for Lithium-Ion Batteries.

Preparation of porous silicon/carbon microspheres as high performance anode materials for lithium ion batteries

Novel Design of Uniform Si@graphite@C Composite As High-Performance Li-ion Battery Anodes

Simple Synthesis of SiGe@C Porous Microparticles As High-Rate Anode Materials for Lithium-Ion Batteries

Wet-chemical Synthesized MCMB@Si@C Microspheres for High-Performance Lithium-Ion Battery Anodes.

C porous microparticles as high-rate anode materials for lithium-ion batteries

Nano-Si/C microsphere with hollow double spherical interlayer and submicron porous structure to enhance performance for lithium-ion battery anode

Rational-design micro-nanostructure of porous carbon film/silicon nanowire/graphite microsphere composites for high-performance lithium-ion batteries

3-Aminopropyltriethoxysilane-assisted Si@Sio2/Cnts Hybrid Microspheres As Superior Anode Materials for Li-Ion Batteries

Synthesis of a novel porous silicon microsphere@carbon core-shell composite via in situ MOF coating for lithium ion battery anodes

Electrosprayed silicon-embedded porous carbon microspheres as lithium-ion battery anodes with exceptional rate capacities

Carbon coated porous hollow silicon microspheres for high‐capacity and durable lithium storage

Amorphous Carbon Shell on Si Particles Fabricated by Carbonizing of Polyphosphazene and Enhanced Performance As Lithium Ion Battery Anode

Mn0.5Co0.5Fe2O4 nanoparticles highly dispersed in porous carbon microspheres as high performance anode materials in Li-ion batteries

Green and facile fabrication of nanoporous silicon@carbon from commercial alloy with high graphitization degree for high-energy lithium-ion batteries

Facile preparation of silicon/carbon composite with porous architecture for advanced lithium-ion battery anode

Electrochemical Performance Enhancement of Porous Si Lithium-Ion Battery Anode by Integrating with Optimized Carbonaceous Materials

High Performance Amorphous-Si@siox/c Composite Anode Materials for Li-ion Batteries Derived from Ball-Milling and in Situ Carbonization

Nonfilling carbon coating of porous silicon micrometer-sized particles for high-performance lithium battery anodes.

Monodisperse Porous Silicon Spheres as Anode Materials for Lithium Ion Batteries