Abstract:Two fluorescent high‐performance polymers based on dicyanoarylamine luminogens were readily synthesized via polycondensation. Both polymers were soluble in several polar aprotic solvents and exhibited useful levels of thermal stability. The polymers were emissive in both solution and solid film states, thereby demonstrating the aggregation‐induced fluorescence changes. Introduction Fluorescent high‐performance polymers have been extensively used in designing optoelectronic devices due to their low cost, excellent thermal stability, high mechanical strength, low flammability, good chemical and radiation resistance, and good electronic properties. While conventional organic luminophores fluoresce strongly in dilute solutions, they suffer from undesirable aggregation‐caused quenching in concentrated solutions and in the solid state due to extensive π‐π stacking interactions and formation of delocalized excitons or excimers. This phenomenon leads to non‐radiative decay thus, decreased fluorescence emission of the material in the solid film state, which significantly limits their real‐world application as solid light‐emitting materials. Objectives To develop new high‐performance polymers with high photo luminescent efficiency, good processability, film‐forming properties, which could potentially be used in the fabrication of optoelectronic devices. Methods The preparation of the polyimide DiCN‐PI was carried out by a one‐step, high‐temperature solution imidization method. In this procedure, 1,2,4,5‐cyclohexanetetracarboxylic dianhydride and the diamine were polymerized in 1‐methyl‐2‐pyrrolidinone and γ‐butyrolactone co‐solvent at 180°C for 15 hours in the presence of isoquinoline as catalyst. On the other hand, polyamide DiCN‐PA was synthesized according to the direct phosphorylation polycondensation technique described by Yamazaki from diamine and trans‐1,4‐cyclohexanedicarboxylic acid using triphenyl phosphite and pyridine as condensing agents. Results and Discussion Both polymers were soluble in several polar aprotic solvents and exhibited useful levels of thermal stability. The polymers were emissive with PL emission bands around 555 (bluish‐green) and 498 (cyan) nm in dilute 1‐methyl‐2‐pyrrolidinone solutions for polyimide and polyamide, respectively. In the solid film state, the polymers emit light green and yellow colors, which simulate the PL behavior of their aggregated states, thereby demonstrating aggregation‐induced fluorescence changes. Conclusions These results indicate that the incorporation of bulky dicyanoarylamine moiety and alicyclic monomer units into the rigid polymer backbones effectively disrupted the planarity of the chain packing which resulted to the fluorescent high‐performance polymers with desired properties for potential optoelectronic applications.

Highly stable electrochromism and electrofluorochromism derived from a bi-functional polyamide containing conjugated bis(diphenylamine-spirodifluorene) moieties

Dual-Switching Electrochromism and Electrofluorochromism Derived from Diphenylamine-Based Polyamides with Spirobifluorene/Pyrene as Bridged Fluorescence Units.

Redox-Stable and Multicolor Electrochromic Polyamides with Four Triarylamine Cores in the Repeating Unit

Concept of triphenylamine side chains with four electroactive nitrogen centers toward record-high stable electrochromic polyamides

Bifunctional D-A type conjugated polymer based on triarylamine-containing oxazole[5,4-d]oxazole/thiazolo[5,4-d]thiazole exhibiting electrofluorochromism and reversible electrochromism

Polymeric optoelectronic materials with low-voltage colorless-to-black electrochromic and AIE-activity electrofluorochromic dual-switching properties

Fluorescence switching of triarylamine-based polyamides with pendant pyrene units and its application in electrochromic smart displays

Boosting electrochromic properties of polyamides through altering the structure bonded to triarylamine groups by xanthene

Triarylamine-based polyamide containing adamantane group as Fe 3+ probe and electrochromic smart devices

Synthesis and Tunable Properties of Oligoaniline-Functionalized Polyamides

Hyperbranched copolymer containing triphenylamine and divinyl bipyridyl units for fluorescent chemosensors

Twisted D–π–A Solid Emitters: Efficient Emission and High Contrast Mechanochromism

Novel triphenylamine polyamides bearing carbazole and aniline substituents for multi-colored electrochromic applications

Colorless Electrochromic/Electrofluorochromic Dual-Functional Triphenylamine-Based Polyimides: Effect of a Tetraphenylethylene-Based π-Bridge on optoelectronic properties

Design and Synthesis of Multi-Coloured Electrochromic and Electrofluorochromic Asymmetric Materials by Adjusting the Central Potential of the Compounds

Semi aromatic colorless polyimide coatings for dual electrochromic and electrofluorochromic displays and its potential for information encryption

Multicolored and durable electrochromism in water soluble naphthalene and perylene based diimides

“Colorless-to-Black” Electrochromic and AIE-Active Polyamides: An Effective Strategy for the Highest-Contrast Electrofluorochromism

Vis-to-NIR electrochromism and bright-to-dark electrofluorochromism in a triazine and thiophene based three-dimensional covalent polymer

Electrofluorochromic and Electrochromic Bifunctional Polymers with Dual-State Emission Via Introducing Multiple C—H···π Bonds

Synthesis, characterization, and photophysical properties of dicyanoarylamine‐based semi‐aromatic polymers