Abstract:Radial shaft sealing rings (RSSR) are important machine elements used in rotating and oil lubricated systems. Their main task is to prevent oil from exiting the system and dirt particles from entering the system. When this function is not fulfilled, a leakage can occur and cause excessive damage after certain operating times, such as gear failure due to insufficient lubrication. This is the reason for the high level of current research interest in seals. The sealing function of RSSR occurs in the contact area between the sealing lip and the shaft. The contact takes place over a very small contact width of approximately 1 μm. These extremely small dimensions and the complex relationships between the functional influencing variables on the radial shaft sealing system make it difficult to simulate wear on the sealing ring. The energetic consideration of the wear process offers the possibility of quantifying influencing variables more easily by their energetic contribution, which can be determined experimentally. Based on experimentally measured total friction moments, and with the help of a semi-analytical (SA) solid contact model based on the half-space theory, this paper presents a modelling approach for the calculation of wear at the sealing ring. The model presented in this work differs from the existing models in two ways. The first particularity is the coupling of SA method with finite element method (FEM) for the resolution of the contact between the sealing lip and the shaft, allowing a fine discretization of the contact zone (by SA method) and the consideration of the structural behavior (by FE method). The SA method compared to the commonly used FEM presents a great saving in computation time. The second particularity is the use of the real data obtained during the wear tests. Most existing simulation models are based purely on contact pressure. This means that through the contact pressure obtained by simulation and a given sliding distance value, a friction energy will be estimated which will be used in a next step using a wear model such as Archad’s to calculate the wear rate. In this publication the value of friction energy was obtained directly on an experimental basis and a more appropriate wear law, such as Fleischer’s, taking into account the friction conditions, was used to estimate the wear rate.

Wear Processes in a Mechanical Friction Clutch: Theoretical, Numerical, and Experimental Studies

Numerical and Experimental Research on Engagement Process of Wet Multi-Plate Friction Clutches with Groove Consideration

Experimental and Theoretical Analysis of the Drag Torque in Wet Clutches

Parametric Analysis of the Drag Torque Model of Wet Multi-Plate Friction Clutch with Groove Consideration

Simulation and Experiment on Dynamic Engagement Characteristics of Wet Clutch

Influences of the Contact State between Friction Pairs on the Thermodynamic Characteristics of a Multi-Disc Clutch

Parametric analysis of wear factors of a wet clutch friction material with different groove patterns

Sliding State Analysis of Fractal Rough Interface Based on the Finite Element Method

Effects of Automotive Test Parameters on Dry Friction Fiber-Reinforced Clutch Facing Surface Microgeometry and Wear—Part 3 Tribological Parameter Correlations and Simulation of Thermo-Mechanical Tribological Contact Behavior

Influence of Material Parameters on the Contact Pressure Characteristics of a Multi-Disc Clutch

Investigation of thermal behavior of a novel multi-conical friction pair during wet clutch's engagement based on finite difference method

Torque capacity of multidisc wet clutch with reference to friction occurrence on its spline connections

Life Cycle Prediction and Evaluation of Clutch Friction Plate Considering Wear Models and Thermal Stress

Control-oriented modeling of wet clutch friction considering thermal dynamics

Analytical simulation of influential parameters affecting grooved wet clutches performance underdisengagement condition

Investigating Failure Modes and Performance Impacts of Wet Clutches in Automotive Limited Slip Differentials

Modeling of the Drag Torque of the Disengaged Grooved Wet Clutches with Waviness

Friction behavior of innovative carbon friction linings for wet multi-plate clutches

Nonlinear Dynamic Characteristics of Rub-Impact Process at High Circumferential Velocities in No-Load Multiplate Wet Clutch

Friction Energy-Based Wear Simulation for Radial Shaft Sealing Ring

An Integrated Approach for Friction and Wear Simulation of Tire Tread Rubber. Part I: Friction Test, Characterization, and Modeling