Abstract:The current work aims to compare the effects of systematic A-site substitutions on the electrical properties of potassium sodium niobate (KNN)-based coating. The A-site elements were replaced by Li+ to form (K0.4675Na0.4675Li0.065) NbO3 (KNLN). The pure KNN coating and the Li+-doped potassium sodium niobate (KNLN) coating with dense morphology and single perovskite structure were successfully prepared by supersonic plasma spraying, and the phase composition, microscopic morphology and electrical properties of the two coatings were compared and analyzed in detail by XRD, XPS, three-dimensional morphology and SEM on an Agilent 4294A (Santa Clara, CA, USA) and FE-5000 wide-range ferroelectric performance tester. The results show that: as the polarization voltage increases, the pure KNN coating is flatter and fuller, but the leakage current is large. The KNLN coating has a relatively long hysteresis loop and is easily polarized. The domain deflection responds faster to the external electric field, and the resistance of the domain wall motion to the external electric field is small. The dielectric constant of KNLN coating is 375, which is much higher than that of the pure KNN coating with 125, and the dielectric loss is stable at 0.01, which is lower than that of pure KNN coating at 0.1–0.35. This is because Li+ doping has successfully constructed a polycrystalline phase boundary in which O-T phases coexist, and has higher dielectric properties, piezoelectric properties and ferroelectric properties. At the same time, due to the high-temperature acceleration process in supersonic plasma spraying, the violent volatilization of the alkaline elements Li+, Na+ and K+ leads to the presence of oxygen vacancies and part of Nb4+ in the coating, which seriously affects the electrical properties of the coating.

Influence of Niobium Pentoxide Phase and Calcination Route on the Formation of Potassium Sodium Niobate Powders

Effects of Na Excess on the Preparation and Characterization of (K0.5na0.5)nbo3ceramics

Phase Evolution and Surface Morphology of Niobate Hydrate Template Nanoparticles Synthesized by Hydrothermal Method

The effect of ZnO and MnO2 as sintering aids in the preparation of potassium sodium niobate ceramics and electrical characterizations

Effects of processing parameters on the synthesis of (K0.5Na0.5)NbO3 nanopowders by reactive high-energy ball milling method

Synthesis and Characterization of Nanocrystalline Niobates

Influence Of Double Calcination-Milling Route On The Structural And Microstructural Properties Of Lead-Free K0.5Na0.5Nbo3 (Knn) Ceramics

Hydrothermal Synthesis and Characterization of KxNa(1−x)NbO3Powders

Phase Transition and Morphology Evolution of Superfine NaNbO3 Particles Synthesized by the Hydrothermal Method with the Assistance of K+

LOW-TEMPERATURE PREPARATION OF NANO-CRYSTALLINE LITHIUM NIOBATE POWDERS BY THE POLYMERIC PRECURSOR METHOD

Alkali Niobate Powder Synthesis Using an Emerging Microwave-Assisted Hydrothermal Method

Improvement in Synthesis of (k0.5na0.5) Nbo3 Powders by Ge4+ Acceptor Doping

Composition Regulation of Potassium Sodium Niobate Thin Films Through Post-Annealing under Alkali Element Atmospheres

Sintering of Lead-Free Piezoelectric Sodium Potassium Niobate Ceramics

Mechanochemical Synthesis Of Kxna1-Xnbo3 Powders

Electrical Properties of Li+-Doped Potassium Sodium Niobate Coating Prepared by Supersonic Plasma Spraying

Characterization of (K0.5Na0.5)NbO3 powders and ceramics prepared by a novel hybrid method of sol–gel and ultrasonic atomization

Effect of sol–gel synthesis method on the structural, electrical, and ferroelectric properties of lead-free K0.5Na0.5NbO3 ceramic

Influence of P2O5 and SiO2 addition on the phase, microstructure, and electrical properties of KNbO3

The Effect of Calcination Temperature on the Structure and Performance of Nanocrystalline Mayenite Powders

Compositional Inhomogeneity and Segregation in (k0.5na0.5)nbo3 Ceramics