Abstract:Purpose. Research of cutting force components during machining of high-hard cast iron by special prefabricated cutters with brazed niborite and ciborite inserts. Determination of the influence of geometric characteristics of the cutting tool, cutting modes and hardness of the material being machined on the cutting forces. The methods. The research methods were based on the fundamentals of cutting theory and cutting tools, material science properties of the tool and processed material. A research bench with special equipment was used. Findings. The nature of the change in the components of cutting forces with depth t, feed rate S and cutting speed v was experimentally investigated. The studies have shown an excess of the resulting force in the horizontal plane Pv over the circumferential one Pz, which is the main feature of turning high-hard metals. It has been established that the main limiting factors in the wear of tool cutting inserts are the permissible levels of forces. The hardness of HB has the greatest effect on the radial force Py. Under identical turning conditions for materials with a hardness of 220 to 610 HB, the forces Pz, Py and Px increase by 1,7; 3,3 and 2,3 times, respectively. In addition to the natural increase, the ratio of cutting forces also changes. Reducing the front angle of the blade causes a deterioration in chip formation conditions and leads to an increase in all components of the cutting forces. An increase in the radius at the top of the cutter r causes an increase in the width and decrease in the thickness of the layer to be cut, as well as a decrease in the main angle in the plan φr on the radial part of the blade. The originality. A complex dependence in the structural-stage form was obtained, which gives a clear picture of the influence of each parameter of the turning process on its performance. This dependence is a mathematical model for calculating the optimal operating and geometric parameters of the turning process of high-hard cast irons. The influence of the frontal angle γ, wear value h, and hardness of HB cast iron on the power characteristics during machining of high-hard cast irons has been studied. Practical implementation. It has been shown that it is economically advantageous to maximize the wear of cutting inserts made of relatively expensive composites. In this case, it is necessary to use a technological system of machine-workpiece-tool of high rigidity.

Effect of PCBN tool grade and cutting type on hard turning of high-chromium white cast iron

Influences of Micro Mechanical Property and Microstructure on Performance of Machining High Chromium White Cast Iron with Cbn Tools

Experimental Investigation on the Machinability of PCBN Chamfered Tool in Dry Turning of Gray Cast Iron

Performance Assessment of Pcbn and Bcbn Tools in Machining of High-Chromium White Cast Iron

Study of cutting forces during turning of high-hard cast irons

Wear performance and mechanisms of PCBN tools in boring of powder metallurgy steels

Cutting Performance and Wear/Damage Characteristics of PCBN Tool in Hard Milling

Research on PCBN Tool Dry Cutting GCr15

Evaluation of wear mechanisms of PVD and CVD coatings deposited on cemented carbide substrates applied to hard turning

Performance analysis of conventional and high-feed turning tools in machining the thermally affected zone after plasma arc cutting of low carbon manganese-alloyed steel

The impact of mechanical properties on the cutting performance of Al2O3-based ceramic cutting tools for green turning of hardened steel

Cutting performance of coated carbide inserts in hard turning of hardened AISI D2 cold work tool steels

Experimental Study on Cutting Force and Tool Wear of PCBN Tools in High-speed Turning Nickel-based Superalloy

Effects of Process Parameters on White Layer Formation and Morphology in Hard Turning of Aisi52100 Steel

Performance and wear mechanisms of coated PCBN tools in high-speed turning superalloy GH4202

Tool life assessment of high strength cast iron alloys in dry face milling operations

Experimental Investigation of Surface Integrity in Finish Dry Hard Turning of Hardened Tool Steel at Different Hardness Levels

Characterisation and machinability of high chromium hardened white cast iron with and without the addition of niobium

Experimental Study On Performance Of Cbn-Coated, Cbn-Uncoated And Pcd Tools In Turning Al 2124 Sic (45%Wt) Pmmc

Experimental Investigation on the Surface Integrity of Hard Machined Components by Super-finish Turning

Performance and wear mechanisms of PCD and pcBN cutting tools during machining titanium alloy Ti6Al4V