Abstract:It has been reported that a novel multi-component styrene-butadienestyrene composite (SBSC) modifier composed of the SBS as the main content and additional components including ethyl-vinyl-acetate (EVA), maleic anhydride grafted with ethyl-vinyl-acetate (MAH-g-EVA), naphthenic oil, and antioxidant can be produced by melt blending. This SBSC modifier can be directly mixed with bitumen and aggregate to prepare bitumen mixture, thus thoroughly addressing inferior thermal storage stability of SBS-modified bitumen. However, it is necessary to explore the efficient utilization of the SBSC modifier due to its inadequate engineering application and poor dispersion when the SBSC modifier was added directly to the bitumen mixture. The objective of this research was to investigate the feasibility of using the SBSC modifier to obtain modified bitumen with acceptable thermal storage stability and other enhanced properties. Modified bitumens (SBSC-modified bitumens with 3, 4, 5, 6, 7 % SBSC modifier content, SBS-modified bitumen with 4.5 % SBS modifier content as the control sample) were prepared. The thermal storage stability of modified bitumen was investigated by the segregation test. Besides, the basic physical properties of modified bitumen were tested, including penetration, softening point, and ductility. The rheological properties were evaluated by temperature sweep test, multiple stress creep recovery (MSCR) test, rotational viscosity (RV) test and bending beam rheometer (BBR) test, respectively. Meanwhile, fluorescence microscopy and Fourier transform infrared (FTIR) spectrometer were also applied to characterize the microproperties of the modified bitumen. Results show that the difference in softening point of SBSC-modified bitumens with modifier contents ranging from 3 % to 7 % is less than 2.5 degrees C after 72 h of high temperature storage at 163 degrees C. The softening point and ductility of SBSC-modified bitumen increase considerably with the addition of the SBSC modifier but the decrements of penetration are not significant. Besides, with the increasing addition of the SBSC modifier, complex modulus, average percent recovery, and viscosity of modified bitumen all improve. Meanwhile, phase angle, non-recoverable creep compliance of modified bitumen decrease. The flexural creep stiffness also decreases with the increasing content of the SBS modifier. When the SBS content is the same, the SBSC-modified bitumen gets better thermal storage stability, high and low temperature properties than the SBS-modified bitumen. The microproperties show that the SBSC modifier can be uniformly dispersed in base bitumen and physically mixed with the base bitumen. The SBSC-modified bitumen obtains preferable thermal storage stability. The high and low temperature properties of the bitumen are also enhanced by the addition of the SBSC modifier. Meanwhile, the melt blending method does not restrict the role of the additional components in the SBSC modifier to improve the performance of bitumen. Based on the above findings, it can be considered that the use of SBSC modifier to prepare modified bitumen with enhanced performance is a promising practice. This research may shed light on the application of SBSC modifier to bitumen pavements.

Effect of layered double hydroxides on ultraviolet aging resistance of SBS modified bitumen membrane

Thermal storage stability and rheological properties of multi-component styrene-butadiene-styrene composite modified bitumen

Preparation and characterization of lignin grafted layered double hydroxides for sustainable service of bitumen under ultraviolet light

Thermal Behaviour And Improved Properties Of Sbr And Sbr/Natural Bitumen Modified Bitumens

Evaluation of the improved properties of SBR/weathered coal modified bitumen containing carbon black

Comparative Analysis of Rheological and Microscopic Performance of SBS Modified Asphalt Based on Field Aging and Laboratory Aging

Rheological properties of asphalt modified by supramolecular UV resistant material-LDHs

Research on low temperature rheological behavior of aging resistant bitumen and mixture

Impact of Ultraviolet Radiation on the Aging Properties of SBS-Modified Asphalt Binders

Effects of Different Antioxidant Intercalated Layered Double Hydroxides on Anti-Aging Properties of Asphalt Binders

Cost-Effective Enhancement of High Viscosity Modified Bitumen Anti-Aging Properties Using Organic Layered Double Hydroxide/Fume Silica Nanoparticles Composite Nanomaterials

Laboratory Investigation of Storage Stability and Aging Resistance of Slightly SBS-Modified Bitumen Binders

Influence of High Viscosity Petroleum Resin (HV-PR) on the Intermediate and High Temperature Performances of Styrene–Butadiene–Styrene Block Copolymer (SBS) Modified Bitumen

Investigation of Antiaging Performance and Service Life of OMMT/SBS Modified Bitumen Waterproof Membranes

Intercalation of p-methycinnamic acid anion into Zn-Al layered double hydroxide to improve UV aging resistance of asphalt

Multiscale characterization of the UV aging resistance and mechanism of light stabilizer-modified asphalt

Binary Heterojunctions of Mg/Al-LDH and Carbon-based Matrixes Derived From Self-assembly Synthesis for Inhibition of Pyrene Photopolymerizing: Elucidation of LDHs Protecting Bitumen Against UV Aging

Effects of solvent-free bentonite fluid on physical, rheological and aging properties of SBS modified bitumen

Development Mechanism of Aging Depth of Bitumen with Increasing UV Aging Time

Experimental Investigation on the Performance of SBS-Modified Asphalt Waterproofing Membrane by Thermo-Oxidative Aging and Freeze–Thaw Cycle

Microstructure, Fatigue, and Self-Healing Properties of SBS-Modified Asphalt under Ultraviolet Radiation