Abstract:Water-foamed injection molding (WFIM) uses conventional injection molding (CIM) with water as a physical foaming agent. Compared to CIM, WFIM is a much more complicated process. As such, it is critical to determine the processing conditions for fabricating quality parts using WFIM. We used the design of experiment (DOE) method based on the Taguchi method to determine the influence of the processing conditions on the morphological structure and ductility of PP/LDPE WFIM parts, which were investigated by tensile testing and scanning electron microscopy (SEM). Our research suggests that fabricating PP/LDPE super-ductile parts using WFIM is indeed feasible. Our research also indicates that there is a close relationship between the ductility and the foamed structures, both of which are deeply influenced by the processing conditions. The analysis of variance results shows further that the water content had the greatest influence on the ductility, followed by the melt temperature, packing time, packing pressure, and PP/LDPE ratio. However, the ductility was only slightly influenced by the mold temperature, injection pressure, and injection time in WFIM. As to the number of cells, the order of influence was melt temperature, water content, packing time, packing pressure, mold temperature, injection pressure, PP/LDPE ratio, and injection time, in that order. In addition, applying DOE is a quite effective method for deducing the optimal set of effective factors in WFIM to produce super-ductile parts with a maximum number of cells. To our knowledge, this is the first time that the relationship among the processing conditions, ductility, and foamed structure of PP/LDPE WFIM super-ductile parts has been investigated and reported.

Effect of processing parameters on essential work of fracture toughness of LLDPE blown films

The Microstructure-Tensile Property Relationship of Polyethylene Resin for Biaxially Stretched Film

Blown Film of M-Lldpe Using a Novel Eccentric Rotor Extruder

A Real‐time WAXS and SAXS Study of the Structural Evolution of LLDPE Bubble

Effect of Mixing Poly(lactic Acid) with Glycidyl Methacrylate Grafted Poly(ethylene Octene) on Optical and Mechanical Properties of the Blown Films

Influence of the Main Blown Film Extrusion Process Parameters on the Mechanical Properties of a High-Density Polyethylene Hexene Copolymer and Linear Low-Density Polyethylene Butene Copolymer Blend Used for Plastic Bags

From Molecular Entanglement Network to Crystal-Cross-Linked Network and Crystal Scaffold During Film Blowing of Polyethylene: an in Situ Synchrotron Radiation Small- and Wide-Angle X-ray Scattering Study

Study on properties of HDPE/LLDPE/POE blown films

Synergistic and Competitive Effects of Temperature and Flow on Crystallization of Polyethylene during Film Blowing

Combined Processing of Polypropylene Film by Coextrusion and Zone‐annealing

Structural Evolution of Hard-Elastic Polyethylene Cast Film in Temperature-Strain Space: an In-Situ SAXS and WAXS Study

Structure-property correlation of polyvinyl alcohol films fabricated by different processing methods

Film Blowing of Linear and Long-Chain Branched Poly(ethylene terephthalate)

Effects of Process Parameters in Thermoforming of Unidirectional Fibre-Reinforced Thermoplastics

Influence of Processing Conditions on the Morphological Structure and Ductility of Water-Foamed Injection Molded PP/LDPE Blended Parts

The Effect of Process Parameters on the Properties of Elastic Melt Blown Nonwovens: Air Pressure and DCD

Elucidation of the relationships of structure-process-property for different ethylene/α-olefin copolymers during film blowing: An in-situ synchrotron radiation X-ray scattering study

Tearing properties, crystallization behavior, microstructure, and morphology of LLDPE with different short branched chain distributions

Process-Induced Morphology of Poly(Butylene Adipate Terephthalate)/Poly(Lactic Acid) Blown Extrusion Films Modified with Chain-Extending Cross-Linkers

Plasticization Effect of Poly(Lactic Acid) in the Poly(Butylene Adipate–co–Terephthalate) Blown Film for Tear Resistance Improvement

Poly(lactide-co-trimethylene carbonate) and polylactide/polytrimethylene carbonate blown films