Abstract:This paper describes the research carried out in the European Commission co-funded project LEMCOTEC (Low Emission Core Engine Technology), which is aiming at a significant increase of the engine overall pressure ratio. The technical work is split in four technical sub-projects on ultra-high pressure ratio compressors, lean combustion and fuel injection, structures and thermal management and engine performance assessment. The technology will be developed at subsystem and component level and validated in test rigs up to TRL5. The developed technologies will be assessed using three generic study engines (i.e. regional turbofan, mid-size open rotor, and large turbofan) representing about 90% of the expected future commercial aero-engine market. Two additional study engines from the previous NEWAC project will be used for comparison. These are based on intercooled and intercooled-recuperated future engine concepts. The compressor work is targeting efficiency, stability margin and flow capacity by improved aerodynamic design. High-pressure and intermediate-pressure compressors are addressed. The mechanical and thermo-mechanical functions, including the variable-stator-systems, will be improved. Axial-centrifugal compressors with impeller and centrifugal diffuser are under investigation too. Three lean burn fuel injection systems are developed to match the technology to the corresponding engine pressure levels. These are the PERM (Partially Evaporating Rapid Mixing), the MSFI (Multiple Staged Fuel Injection) and the advanced LDI (Lean Direct Injection) combustion systems. The air flow and combustion systems are investigated. The fuel control systems are adapted to the requirements of the ultra-high pressure engines with lean fuel injection. Combustor-turbine interaction will be investigated. A fuel system analysis will be performed using CFD methods. Improved structural design and thermal management is required to reduce the losses and to reduce component weight. The application of new materials and manufacturing processes, including welding and casting aspects, will be investigated. The aim is to reduce the cooling air requirements and improve turbine aerodynamics to support the high-pressure engine cycles. The final objective is to have innovative ultra-high pressure-ratio core-engine technologies successfully validated at subsystem and component level. Increasing the thermal efficiency of the engine cycles relative to year 2000 in-service engines with OPR of up to 70 (at max. condition) is an enabler and key lever of the core-engine technologies to achieve and even exceed the ACARE 2020 targets on CO2, NOx and other pollutant emissions: • 20 to 30 % CO2 reduction at the engine level, exceeding both, the ACARE 15 to 20% CO2 reduction target for the engine and subsequently the overall 50% committed CO2 and the fuel burn reduction target on system level (including the contributions from operations and airframe improvements), • 65 to 70 % NOx reduction at the engine level (CAEP/2) to attain and exceed the ACARE objective of 80% overall NOx reduction (including the contributions from both, operational efficiency and airframe improvement), reduction of other emissions (CO, UHC and smoke/particulates) and • Reduction of the propulsion system weight (engine including nacelle without pylon).

Generalized Thermodynamic Assessment of Concepts for Increasing the Efficiency of Civil Aircraft Propulsion Systems

Conceptual Design and Optimization of Scramjet Engines Using the Exergy Method

Identification of Potential Efficiency Opportunities in Internal Combustion Engines Using a Detailed Thermodynamic Analysis of Engine Simulation Results

First and Second Law Analysis of Intercooled Turbofan Engine

Thermal Management Systems for Civil Aircraft Engines: Review, Challenges and Exploring the Future

Performance assessment for a novel supersonic turbine engine with variable geometry and fuel precooled: From feasibility, exergy, thermoeconomic perspectives

A Comprehensive Evaluation of Ducted Fan Hybrid Engines Integrated with Fuel Cells for Sustainable Aviation

Conceptual study of a mechanically integrated parallel hybrid electric turbofan

Analysis of the aerothermal performance of modern commercial high-pressure turbine rotors using different levels of fidelity

LEMCOTEC: Improving the Core-Engine Thermal Efficiency

Parametric Thermal Analysis of Intercooled and Recuperated Turbofan Engine

Development of a Gas Turbine Concept for Electric Power Generation in a Commercial Hybrid Electric Aircraft

Thermal power plant upgrade via a rotating detonation combustor and retrofitted turbine with optimized endwalls

Thermodynamics Analysis of a Turbojet Engine Integrated with a Fuel Cell and Steam Injection for High-Speed Flight

A Method to Improve the Efficiency of an Electric Aircraft Propulsion System

Unified Assessment of Open and Ducted Propulsors

Thermodynamic analysis for a novel chemical precooling turbojet engine based on a multi-stage precooling-compression cycle

Aero-Propulsive Efficiency Requirements for Turboelectric Transport Aircraft

Comparative analysis of turboshaft engines thermodynamic cycles calculation

Performance analysis of a gas turbine engine with intercooling and regeneration process - Part 1

Analysis of Recuperation Supercritical Carbon Dioxide Cycle for Heat Recovery of an Aircraft Engine