Abstract:Hip and knee joint replacements are common and largely successful procedures that utilise implants to restore mobility and relieve pain for patients suffering from e.g. osteoarthritis. However, metallic ions and particles released from both the bearing surfaces and non-articulating interfaces, as in modular components, can cause hypersensitivity and local tissue necrosis, while particles originating from a polymer component have been associated with aseptic loosening and osteolysis. Implant coatings have the potential to improve properties compared to both bulk metal and ceramic alternatives. Ceramic coatings have the potential to increase scratch resistance, enhance wettability and reduce wear of the articulating surfaces compared to the metallic substrate, whilst maintaining overall toughness of the implant ensuring a lower risk of catastrophic failure of the device compared to use of a bulk ceramic. Coatings can also act as barriers to inhibit ion release from the underlying material caused by corrosion. This review aims to provide a comprehensive overview of wear-resistant coatings for joint replacements - both those that are in current clinical use as well as those under investigation for future use. While the majority of coatings belong predominantly in the latter group, a few coated implants have been successfully marketed and are available for clinical use in specific applications. Commercially available coatings for implants include titanium nitride (TiN), titanium niobium nitride (TiNbN), oxidized zirconium (OxZr) and zirconium nitride (ZrN) based coatings, whereas current research is focused not only on these, but also on diamond-like-carbon (DLC), silicon nitride (SiN), chromium nitride (CrN) and tantalum-based coatings (TaN and TaO). The coating materials referred to above that are still at the research stage have been shown to be non-cytotoxic and to reduce wear in a laboratory setting. However, the adhesion of implant coatings remains a main area of concern, as poor adhesion can cause delamination and excessive wear. In clinical applications zirconium implant surfaces treated to achieve a zirconium oxide film and TiNbN coated implants have however been proven comparable to traditional cobalt chromium implants with regards to revision numbers. In addition, the chromium ion levels measured in the plasma of patients were lower and allergy symptoms were relieved. Therefore, coated implants could be considered an alternative to uncoated metal implants, in particular for patients with metal hypersensitivity. There have also been unsuccessful introductions to the market, such as DLC coated implants, and therefore this review also attempts to summarize the lessons learnt.

Titanium-Nitride Coating of Orthopaedic Implants: A Review of the Literature

Retrieval Analysis of Titanium Nitride Coatings for Orthopaedic Implants

Current status and future potential of wear-resistant coatings and articulating surfaces for hip and knee implants

Application of PVD TiN coating to Co-Cr-Mo based surgical implants

Retrieval study of commercially available knee implant coatings TiN, TiNbN and ZrN on TiAl6V4 and CoCr28Mo6

Experimental investigation of tribo-mechanical and chemical properties of TiN PVD coating on titanium substrate for biomedical implants manufacturing

Key Challenges in Diamond Coating of Titanium Implants: Current Status and Future Prospects

Mechanical, biocorrosion, and antibacterial properties of nanocrystalline TiN coating for orthopedic applications

Bioactivity of TiN-coated titanium implants

Surface nano-architectures and their effects on the mechanical properties and corrosion behavior of Ti-based orthopedic implants

Surface modification of Ti6Al4V alloy via advanced coatings: Mechanical, tribological, corrosion, wetting, and biocompatibility studies

No clinical benefit of titanium nitride coating in cementless mobile-bearing total knee arthroplasty

New Ti-Alloys and Surface Modifications to Improve the Mechanical Properties and the Biological Response to Orthopedic and Dental Implants: A Review

Nanofiber Polymers for Coating Titanium-Based Biomedical Implants

Evaluation of tribological and biological properties of Ti6Al4V coated with Si3N4/ND nanoparticles for orthopedic applications: a comprehensive analysis

Orthopedic Coating Materials: Considerations and Applications

Surface modification techniques of titanium and titanium alloys for biomedical orthopaedics applications: A review

Surface Modification of Biomedical Ti and Ti Alloys: A Review on Current Advances

Titanium-Based alloys and composites for orthopedic implants Applications: A comprehensive review

Surface Modification of Orthopedic Implants Based on Titanium Alloys

Opportunities and challenges of the nitride coatings for artificial implants: A review