Abstract:Super hydrophobic surfaces have attracted significant attention recently, and various preparing methods have been reported, such. as sol-gel method, plasma etching, phase separation, template-based extrusion and so on. Besides them, the solvent evaporation-phase separation was a relatively simple one, but only polymers with particular structure, such as block copolymers and polymer blends, were successfully applied by this method, Moreover, some complicate post-procedures or rigorous special environments were often essential. Herein we reported a simple way to facile a super-hydrophobic surface of random copolymers just by one-step casting the polymer solution onto a solid surface. The films had many micro- and nano-scale convexities and grooves with multiplex structures distributed on the surface, which appeared like a lotus leaf surface.. The micro-scale roughness and low surface energy together endowed the films excellent super-hydrophobic ability even without further modification. The water contact angle was about 155 degrees - 160 degrees, and the sliding angle was less than 3 degrees.The random copolymers of metharcylate (MMA) and perfluoroalkylethyl acrylate (FMA) were synthesized by micro-emulsion polymerization. The polymerization was carried out with sodium dodecylsulfate-C7F15 COONH4-n-butanol as emulsifier, K2S2O8-NaHSO3-CuSO4 redox as initiator. The emulsion was poured into excess methanol and washed by water. Then the polymer was purified several times by dissolving in acetone and precipitation by methanol. The copolymers were characterized by H-1-NMR, FTIR, GPC and fluorine element analysis. Super-hydrophobic films were prepared by a one-step casting process. First, the copolymers were dissolved in F-113 to form homogeneous solutions, and then cast on 2 cm x 2 em clean glass plates at pre-set temperatures in windtight environment. When the solvent was evaporated, super-hydrophobic films were formed. It was found that when a good solvent of PMMA was used, such as tetrahydrofuran (THF), acetone, etc., or the mixed solvents of THF-F113, acetone-F113 etc., a smooth surface with water contact angles less than 130 was obtained. A super-hydrophobic film could not gotten at these cases. It was regarded that the movement and interpretation of copolymer segments had dominative effects on the films morphology.The concentration of the polymer solution had great effect on the morphology of the films prepared. The casting solution concentration should be in an appropriate scale, the best concentration (c) was about 5 x 10(-3) g/mL <= c <= c(0), where c(0) was the critical concentration of copolymer in F113. What was more, the temperature and pressure should also be proper.The possible reason of leading to the super-hydrophobic properties of these films was due to the combination of micro- and nano-scale binary roughness and low surface energy. The mechanism of forming these films based on the micelle aggregation model and was further discussed in this paper. These special films with both many convexities and grooves were formed because of the intrinsic properties of the random copolymer and a proper solution concentration as well as the forming conditions.In conclusion, using F113 as solvent, PFMA-PFMA random copolymers can. facile super-hydrophobic surfaces by the solvent evaporation-phase separation method.

Fabrication of a superhydrophobic LLDPE film by thermal lamination and peeling

Mechanically stable superhydrophobic polymer films by a simple hot press lamination and peeling process

Preparation and characterization of super hydrophobic aerogel coated ultra-high molecular weight polyethylene fabric

Superhydrophobic poly(vinylidene fluoride) film fabricated by alkali treatment enhancing chemical bath deposition

Super-hydrophobic and Self-cleaning PVDF Film Fabricated by Chemical Bath Deposition

Femtosecond laser processing of steel template for mass production of superhydrophobic polyethylene film

Fabrication of Superhydrophobic Surface by a Laminating Exfoliation Method

Surface Modification Of Linear Low-Density Polyethylene Film By Amphiphilic Graft Copolymers Based On Poly(Higher Alpha-Olefin)-Graft-Poly(Ethylene Glycol)

Biomimetic Superhydrophobic Polyolefin Surfaces Fabricated with a Facile Scraping, Bonding and Peeling Method

Preparation of Bonded Super-hydrophobic Thin Film

Polylactide Films with Superhydrophobicity and Superior Mechanical Properties Constructed by Combining Annealing Stretching and Nonsolvent-Induced Phase Separation

Study on preparation of super-hydrophobic polypropylene via phase separation

Facile Fabrication of Superhydrophobic Nanocomposite Coatings Based on Water‐Based Emulsion Latex

Direct Catalytic Route To Superhydrophobic Polyethylene Films

Superhydrophobic Polyethylene Films by Catalytic Ethylene Polymerization

Carbon Quantum Dots-Driven Surface Morphology Transformation Towards Superhydrophobic Poly(lactic Acid) Film

PREPARATION OF SUPER-HYDROPHOBIC FILMS WITH PERFLUOROALKYLETHYL ACRYLATE RANDOM COPOLYMERS

Superhydrophobic Modification of Polyimide Films Based on Gold-Coated Porous Silver Nanostructures and Self-Assembled Monolayers

Valorization of mixed plastics waste for the synthesis of flexible superhydrophobic films

One‐step Fabrication of Fluoropolymer Transparent Films with Superhydrophobicity by Dry Method

Biomimetic Superhydrophobic Films with an Extremely Low Roll-Off Angle Modified by F16CuPc via Two-Step Fabrication