Abstract:This study proposes a detailed Parabolic Trough Collector (PTC) 1D model offering precise optical and thermal analysis. Our motivations were accuracy while ensuring fast and inexpensive computation. The proposed model differs from existing models by considering a more extensive set of possible optical and thermal losses, which to our knowledge have not previously been grouped together in a single model. Testing of the model based on experiments carried out by Sandia National Laboratories showed near-similar accuracy to much more complex models, with a mean standard deviation of 0.891% and 5.99 W/m 2 for thermal efficiency and thermal losses respectively. These tests were carried out using two types of selective coating: cermet and black chrome, with two operating modes, namely vacuum and pressure annulus. To expand its scope of validity, the developed model was also tested using data from a selection of PTCs of commercial lengths (70, 106, 143, and 150 m) under real operating conditions. Additional validation of the model was carried out with available results from different heat transfer fluids (HTF), including two nanofluids. We highlighted that the deviation from the results of the various PTCs, although very satisfying in general, becomes more critical with increasing length and temperature, reaching a maximum outlet temperature deviation of around 2.14 °C. On the other hand, when switching from water to the nanofluid Water/CuO (5 %), the results show an increase in outlet fluid temperature from 325.91 to 334.73 °C. Experimental validation was also carried out using a 25 kW PTC test loop located at Ben Guerir. The average relative error perceived between simulation results and experimental measurements is estimated at 0.99 % for the steady-state test (based on the HTF temperature at the PTC outlet). An additional validation based on the external temperature of the glass envelope was also considered. This approach, which is rarely used in the literature, showed a relative error of around 4.39 % between simulations and experimental data, which remains within the uncertainty range of the thermal camera used.

Numerical Simulation, Design, and Construction of a Double Glazed Compound Parabolic Concentrators-Type Integrated Collector Storage Water Heater

Thermal assessment of cylindrical parabolic integrated collector storage using input-output and dynamic system testing procedures: Experimental and numerical study

Numerical Simulation On The Optical And Thermal Performance Of A Modified Integrated Compound Parabolic Solar Concentrator

An innovative asymmetrical CPC with integrated PCM as an in-line water heater

Experimental Investigation to Determine the Performance of Solar Thermal Collector with Single and Double Glazing

Numerical Study of a Novel Miniature Compound Parabolic Concentrating Photovoltaic/thermal Collector with Microencapsulated Phase Change Slurry

A Numerical and Experimental Study of a Dual-Function Solar Collector Integrated with Building in Passive Space Heating Mode

A detailed 1D model of a parabolic trough solar receiver with a double-validation approach

Thermal performance and optimization of an integrated collector–storage solar air heater based on lap joint-type flat micro-heat pipe arrays

Simulated Performance Analysis of a Hybrid Water-Cooled Photovoltaic/Parabolic Dish Concentrator Coupled with Conical Cavity Receiver

Heat transfer analysis and thermal performance investigation on an evacuated tube solar collector with inner concentrating by reflective coating

Concentrated Solar Power (CSP) for Sustainable Architecture to Supply Domestic Hot Water and Heating Loads of Buildings

Photothermal conversion performance based on optimized design of multi-section compound parabolic concentrator

Photo-thermal design and analysis of a novel CPC coupled solar air evacuated tube collector

A Numerical Study to Improve the Efficiency of Solar Collector used for water heating using Phase Change Material

Model verification and photo-thermal conversion assessment of a novel facade embedded compound parabolic concentrator

Solar Collector with Asymmetric Compound Parabolic Concentrator for Winter Energy Harvesting and Summer Overheating Reduction: Concept and Prototype Device

Optimization of thermal efficiency on solar parabolic collectors using phase change materials - experimental and numerical study

Numerical Simulation Investigation of a Double Skin Transpired Solar Air Collector

Thermal evaluation of geometrical innovations in concentric and eccentric evacuated single and double solar collectors

Experimental Investigation of Integrated Energy Storage on Thermal Performance Enhancement of Evacuated Glass-Thermal Absorber Tube Collector (EGATC) for Air Heating Application