Abstract:Abstract Combined measurements of shear stress relaxation and differential dynamic storage and loss shear moduli G′ and G′′ have been made on styrene-butadiene rubber (type 1502) containing 50 phr N299 carbon black and 10 phr Sundex 790 oil, both cured and uncured, and compared with similar measurements on the cured and uncured gum rubber. The range of temperature was −22.5° to 63°C, and of static shear strain 0.01 to 0.40; the maximum oscillatory shear strain was about 0.005 and the frequency was usually 0.64 Hz. Dynamic measurements of G′ and G′′ with no superposed static strain and stress relaxation measurements at small strains on the filled samples could be reduced by frequency-temperature superposition with αT shift factors that were somewhat larger than those that applied to the raw or crosslinked gum. At about 0.6 Hz, the filler increased the storage modulus by about a factor of 5 for the cured sample and about 10 for the uncured; the moduli for the cured and uncured filled samples were almost identical. The order of rates of relaxation was unfilled uncured > filled uncured > filled cured > unfilled cured. At small static strains, the stress relaxation of the filled samples (both uncured and cured) was substantial, but the differential dynamic moduli G′ and G′′ remained nearly equal to their values with zero static strain throughout the relaxation process. With increasing static strain γ, the strain-dependent relaxation modulus G(γ;t) decreased by as much as a factor of 3 for the filled, cured sample and 4 for the filled, uncured sample. The modulus G(γ;t) could not be factored into a strain-dependent and a time-dependent function. During stress relaxation of the filled samples (both cured and uncured) at large strains, the differential storage modulus G′(ω,γ;t) experienced a drop followed by slow recovery toward its initial value at 25°C; the loss modulus G′′(ω,γ;t) was unchanged. For the filled, cured sample, complete recovery to the initial value G′(ω,0) (where 0 refers to zero static strain) was accomplished by removing the shearing stress and heating for one day at 63° followed by return of the temperature to 25°C. The results are interpreted in terms of a structure which combines a crosslinked (or, in the case of uncured, an entangled) polymer network and a network of carbon black particles. At small strains, stress relaxation is thought to be accomplished primarily by rearrangements of carbon particles and/or polymer molecules bridging them, without structural damage in the sense that the rearranged structure has the same properties as the original. These rearrangements are impeded by crosslinking in the cured vis-a-vis the uncured filled rubber. The kinetics of rearrangement may be governed by configurational changes of the polymer molecules since the temperature shift factors do not differ greatly from those for the gum rubber. At large strains, the particle network can be damaged but can regain its structure by a healing process which is accelerated at higher temperatures. The conclusions apply to the particular compound studied here and not necessarily to other rubber-black compounds, which according to the literature show great diversity of properties.

Bound rubber morphology and loss tangent properties of carbon-black-filled rubber compounds

Significant Influence of Bound Rubber Thickness on the Rubber Reinforcement Effect

Microstructure effect analysis of carbon black-filled rubber composites

Study of the Effect of Carbon Black Filling on the Mechanical Behavior of Rubber Hyper-Elasticity

Linear Rheology of Natural Rubber Compounds Filled with Silica, Short Nylon Fiber or Both

Experimental Investigation and Constitutive Modeling of Uncured Carbon Black Filled Rubber at Different Strain Rates

Stress Relaxation and Differential Dynamic Modulus of Carbon Black-Filled Styrene-Butadiene Rubber in Large Shearing Deformations

Finite viscoelasticity of filled rubbers: experiments and numerical simulation

Investigation of the Carbon‐Black Network in Natural Rubber Under Cyclic Deformation

Finite viscoelasticity of filled rubbers: the effects of pre-loading and thermal recovery

Relationship Between The Material Properties And Fatigue Crack-Growth Characteristics Of Natural Rubber Filled With Different Carbon Blacks

A Micro-Mechanical Mechanism For Energy Dissipation Of Filled Rubber

Effects of Carbon Black Surface Modification on the Morphology and Properties in Blends with Natural Rubber Studied with High‐Resolution X‐Ray Computed Tomography

Influence of viscoelasticity on the tribological behaviour of carbon black filled nitrile rubber (NBR) for lip seal application

Understanding the Reinforcement and Dissipation of Natural Rubber Compounds Filled with Hybrid Filler Composed of Carbon Black and Silica

Microstructure Evolution and Strain Softening of Carbon Black Filled Natural Rubber Vulcanizates

Energy Dissipation Accompanying Mullins Effect of Nitrile Butadiene Rubber/carbon Black Nanocomposites

Thermomechanical Characterization of Carbon Black Reinforced Rubbers During Rapid Adiabatic Straining

A MICROSCOPY INVESTIGATION OF RUBBER COMPOUND CRACK PRECURSORS AND TENSILE FRACTURE SURFACES

Carbon black networking in elastomers monitored by simultaneous rheological and dielectric investigations

Viscoelastic Behaviors of Carbon Black Gel Extracted from Highly Filled Natural Rubber Compounds: Insights into the Payne Effect