Abstract:Drying is a very important unit operation in many industries such as food, pharmaceuticals, chemicals and ceramics. In most cases, wet materials are dried by forced convection using hot air flow. Heat and mass transfer processes during drying have been studied by both experimental and numerical simulation methods. For the purpose of studying the mechanism of heat and mass transfer and stress-strain distribution during the hot air drying of biological porous medium, two-way coupled thermo-hydro-mechanical mathematical model has been developed to simulate the hot air convective drying process of biological porous media on basis of Fickian diffusion theory, Fourier’s law of heat conduction and thermoelasticity mechanics. The following assumptions were made in order to find a solution to the hot air drying model: the biological porous medium was homogeneous and isotropic; the deformation during drying was elastic. The transient model, composed of a system of partial differential equations, was solved by finite difference methods. The computational procedure was programmed using C language. Some physical and mechanical properties of carrot changing with dry basis moisture content and temperature were considered. The numerical results were compared with available experimental data obtained during the drying of potatoes and carrots. The relative errors between numerical results and experimental data were both less than 5%, which showed the numerical results obtained using the mathematical model were in good agreement with the experimental data. Numerical simulations of the drying curve variations and the spatio-temporal distributions of moisture, temperature and drying stresses and strains of carrot were also evaluated. The temperature and moisture content showed a gradient inside carrot slice during drying. As the drying process proceeded, the temperature inside the carrot slice initially increased to reach the wet bulb temperature of the environment and eventually leveled off. The dry basis moisture content inside the carrot slice decreased, with the fastest decreased at the heat and mass transfer interface, eventually reached the equilibrium moisture content of the potato and leveling off. Both the moisture content gradient and the temperature gradient decreased gradually in the thickness direction. The normal stress was negative in all parts of the carrot slice, and the larger the closer to the evaporation interface. The shear stress was positive in all parts of the carrot slice, and the maximum shear stress occurred in the middle of the carrot slice. As in the case of the normal stress, the values of the normal strain were negative. The change trend of normal strain with time was consistent with that of moisture content. These results indicated that the observed physical deformations were caused by the dehydration of carrot slice during drying. The influence of drying conditions, such as air temperature, air velocity and the thickness of porous media on drying process was analyzed. Analysis showed that under certain drying conditions, the higher air temperature, the greater air velocity and the thinner slice thickness, the shorter drying time. This work should help in developing an understanding of the relationship between mass and heat transfer, shrinkage, stress, strains and physical degradation.

Drying of a Fully Saturated Porous Medium With Excess Water Layers - A Numerical Study

Research progress of numerical simulation on heat and moisture transfer in porous textiles

Numerical modeling of drying from saturated to unsaturated conditions with two-phase partitioning boundaries at the medium surface and interface-dependent phase change

Numerical and experimental investigation of convective drying in unsaturated porous media with bound water

Rate-limiting mechanisms of water removal during the formation, vacuum dewatering, and wet-pressing of paper webs: A review

Experimental analysis of convective drying of paper and board

Mass and Heat Transport Models for Analysis of the Drying Process in Porous Media: A Review and Numerical Implementation

Computational Modelling for Decarbonised Drying of Agricultural Products: Sustainable Processes, Energy Efficiency, and Quality Improvement

A Numerical Implementation of the Soret Effect in Drying Processes

Multiphase modelling of water evaporation and condensation in an air-heated porous medium

Mathematical Model and Numerical Simulation of Biological Porous Medium During Hot Air Drying

Intensification of Paper Drying on Drying Cylinders

Drying Characteristics, Kinetic Modeling, Energy and Exergy Analyses of Water Yam (Dioscorea alata) in a Hot Air Dryer

A fully coupled multiphase model for infrared-convective drying of sweet potato

Simulation and experimental study of heat-moisture-solute transfer during drying process of porous media

On the solution of coupled heat and moisture transport in porous material

Modeling and simulation of drying kinetics/curves: application to building materials

Applicable Methodologies for the Mass Transfer Phenomenon in Tumble Dryers: A Review

Transport phenomena in porous media: A review

Experimental and Theoretical Analysis of the Thermostatic Drying Process in Wetted Porous Sand Beds with Different Pore Sizes

Effect of heat and mass transfer coefficients on force convective drying of porous media