Abstract:In recent decades, geoelectrical methods have played a very important role in near-surface investigation. The most widely used of these methods is electrical resistivity tomography (ERT). Regardless of the forward and inversion algorithms used, the original data collected from a survey is the most important factor for quality of the resulted model. However, 3D electrical resistivity survey design continues to be based on data sets recorded using one or more of the standard electrode arrays. There is a recognized need for the 3D survey design to get better resolution using fewer data. Choosing suitable data from the comprehensive data set is a great approach. By reasonable selecting, better resolution can be obtained with fewer electrodes and measurements than conventional arrays. Previous research has demonstrated that the optimized survey design using the 'Compare R' method can give a nice performance.This paper adds target-oriented selection and modified the original 'Compare R' method. The survey design should be focused on specific target areas, which need a priori information about the subsurface properties. We select electrodes and configurations as the target set by the comprehensive set firstly which meets the requirements of the target area. The number of measurements and electrodes is much less than the comprehensive set and the model resolution matrix takes less time to calculate. At the next step for rank, we calculate the sensitivity matrix of the target set only once and then calculate the contribution degree of each measurement separately from it. The time of iterative calculation of the resolution matrix when measurements set changing is less than the original method.The traditional method of evaluating RMS is not appropriate for comparing the quality of collected data by different survey designs. SSIM (structural similarity index) gives more reliable measures of image similarity better than the RMS. The curves of SSIM values in three dimensions and the average SSIM are given as quantitative comparisons. Besides, the frequency of electrodes utilized given to guides on selecting the highest used electrodes. Finally, the curves of the average relative resolution S and the number of electrodes as the number of measurements increase are given, which proves the method works effectively.The results show the significance of using target-oriented optimized survey design, as it selects fewer electrodes and arrays than the original CR method. Also, it produces better resolution than conventional arrays and takes less calculation time. 3D SSIM, frequency of electrodes used, the relationship between average relative resolution, number of electrodes and number of measurements, these quantitative comparison methods can effectively evaluate the data collected in various survey designs.

Introducing 3D U-statistic method for separating anomaly from background in exploration geochemical data with associated software development

Joint Modeling Based on Singularity Mapping and U-statistical Methods for Geo-Anomaly Characterization

Target-oriented Optimized Survey Design and Quantitative Comparison for 3D Electrical Resistivity Tomography

Intelligent mapping of geochemical anomalies: Adaptation of DBSCAN and mean-shift clustering approaches

Geochemical Anomaly Detection and Pattern Recognition: A Combined Study of the Apriori Algorithm, Principal Component Analysis, and Spectral Clustering

A comprehensive evaluation of OPTICS, GMM and K-means clustering methodologies for geochemical anomaly detection connected with sample catchment basins

Identifying porphyry-Cu geochemical footprints using local neighborhood statistics in Baft area, Iran

Comparative Studies on the Geochemistry Anomaly Extraction in Baiyinguole Area,Inner Mongolia

Multivariate statistical analysis and bespoke deviation network modeling for geochemical anomaly detection of rare earth elements

Two-dimensional Inversion of CSAMT Data and Three-Dimensional Geological Mapping for Groundwater Exploration in Tongkeng Area, Hunan Province, China

Extraction of weak geochemical anomalies based on multiple-point statistics and local singularity analysis

Mapping geochemical singularity using multifractal analysis: Application to anomaly definition on stream sediments data from Funin Sheet, Yunnan, China

Identification of Geochemical Anomalies Based on RPCA and Multifractal Theory: A Case Study of the Sidaowanzi Area, Chifeng, Inner Mongolia

Statistical features of spatial information to g(Au/Ag) - Anomaly in Guilaizhuang gold ore area, Shandong province

Application of Classical Statistics and Multifractals to Delineate Au Mineralization-Related Geochemical Anomalies from Stream Sediment Data: a Case Study in Xinghai-Zeku, Qinghai, China

3D Inversion and 3D Visualization of 2D Survey Data Based on High Density Electrical Method: Take Guilester BarQin Mining Area As an Example

Fractal Analysis of Data Abnormities in Geochemical Exploration in Shungang,Lujiang

A Mineral Resources Quantitative Assessment and 3D Visualization System.

Detecting Statistically Significant Geographical Anomalous Regions from Spatial Sampling Points by Coupling Gaussian Function and Multidirectional Optimization.

Mineral exploration and regional surface geochemical datasets: An anomaly detection and k-means clustering exercise applied on laterite in Western Australia

Estimating Rock Composition from Replicate Geochemical Analyses: Theory and Application to Magmatic Rocks of the GeoPT Database