Abstract:To mitigate PM2.5 emissions is becoming a pressing concern, because these particles pose a threat to public health. Evidence shows that bead-free nanofiber with diameter of <100 nm is more likely to capture the PM2.5, however, currently it is impossible to fabricate bead-free nanofiber with such diameter without introduction of other substances. To fabricate bead-free polyacrylonitrile (PAN) nanofibers with diameter of <100 nm, we improved the electrospinning process of membrane fabrication via design of experiment (DOE), and we then used these nanofibers to filter PM2.5 emissions from burning cigarettes and fused deposition modeling (FDM) three-dimensional (3D) printing. The DOE was based on a L27 (313) orthodoxy array, which consists of six controllable factors, that is, the concentration of solution, the spinning voltage, the rotating speed, the tip-to-collector distance, the flow rate of the syringe pump, and the electrospinning temperature, each of them has three levels. The results showed that the nanofibers of the least diameter (i.e., 77 nm) can be fabricated under the following condition: 8 wt% PAN solution, 12 kV voltage, 5000 r/min, 12 cm tip-to-collector distance, 0.6 ml/h flow rate, and 50 °C electrospinning temperature. Range analysis and analysis of variance (ANOVA) showed that the concentration of PAN solution has the most significant effect on the diameter, and their values are positively correlated. An examination in a two-chamber filtering device showed the PAN membrane with the least fiber diameter has a PM2.5 filtration efficiency of 99.26%. A filtration test on standard FDM 3D printing process showed the membrane has a PM2.5 removal efficiency of 81.16%. This work could mitigate PM2.5 emissions from cigarette tobacco and FDM 3D printing, and it would be used to other scenarios, such as industrial and traffic emissions.

Polyacrylonitrile microscaffolds assembled from mesh structures of aligned electrospun nanofibers as high-efficiency particulate air filters

Polyacrylonitrile/polyimide composite sub-micro fibrous membranes for precise filtration of PM0.26 pollutants

Facile fabrication of reinforced sub-micron fibrous media with hierarchical structure compounded thermally for effective air purification in application

Electrospun PS/PAN Nanofiber Membranes Formed from Doped Carbon Nanotubes with a Fluffy and Multi-scale Construction for Air-Filtration Materials

Antimicrobial Nanofiber Based Filters for High Filtration Efficiency Respirators

A Fluffy Dual‐Network Structured Nanofiber/Net Filter Enables High‐Efficiency Air Filtration

Efficient and reusable polyamide-56 nanofiber/nets membrane with bimodal structures for air filtration

Mass production of polyacrylonitrile sub-micron fibrous webs with different aligned degrees via free surface electrospinning for air purification

Airflow Synergistic Needleless Electrospinning of Instant Noodle‐like Curly Nanofibrous Membranes for High‐Efficiency Air Filtration

Improving the Electrospinning Process of Fabricating Nanofibrous Membranes to Filter PM2.5

Improvement of Aerosol Filtering Performance of PLLA/PAN Composite Fiber with Gradient Structure

Tri-layer gradient structured micro/nanofibrous nonwovens for high filtration efficiency and low air resistance

Preparation of Anti-Layered Polyamide-66/Polyacrylonitrile/Polyethersulfone (Pa-66/Pan/pes) Sandwich Structured Membrane for Air Filtration by Electrospinning

Air filters fabricated by fibrillated lyocell fibres and polyethylene terephthalate fibres with implantation of cellulose nanofibrils for high-efficiency particulate matter removal

Large-Scale Preparation of Polymer Nanofibers for Air Filtration by a New Multineedle Electrospinning Device

Using modified raw materials to fabricate electrospun, superhydrophobic poly(lactic acid) multiscale nanofibrous membranes for air-filtration applications

High-efficiency and super-breathable air filters based on biomimetic ultrathin nanofiber networks

Polyacrylonitrile Nanofiber Membranes Modified with Ni-Based Conductive Metal Organic Frameworks for Air Filtration and Respiration Monitoring

Bioinspired PM2.5 filter: An AgNWs reinforced PAN/PVP composite membrane with the porous and multilayered network structure

Morphology engineering processed nanofibrous membranes with secondary structure for high-performance air filtration

Three-dimensional composite electrospun nanofibrous membrane by multi-jet electrospinning with sheath gas for high-efficiency antibiosis air filtration