Abstract:Bioartificial blends of poly-(epsilon-caprolactone) (PCL) with a polysaccharide (starch, S; dextran, D; or gellan, G) (PCL/S, PCL/D, PCL/G 90.9/9.1 wt ratio) were prepared by a solution-precipitation technique and widely characterized by differential scanning calorimetry analysis (DSC), Fourier transform infrared-attenuated total reflectance spectroscopy (FTIR-ATR), optical microscopy (OM), wide-angle X-ray diffraction analysis (WAXD), and thermogravimetry (TGA). DSC showed that the polysaccharide reduced the crystallinity of PCL and had a nucleation effect, which was also confirmed by OM analysis. Hoffman-Weeks analysis was performed on PCL and blend samples allowing calculation of their equilibrium melting temperatures (). WAXD showed that the crystalline unit cell type was the same for PCL and blends. FTIR-ATR did not evidence interactions between blend components. Thermal stability was affected by the type of polysaccharide. Microparticles (<125 microm) were produced from blends by cryogenical milling and characterized by scanning electron microscopy analysis (SEM). Selective laser sintering (SLS), a new rapid prototyping technology for scaffold fabrication, was applied to sinter blend microparticles according to a PC-designed two-dimensional geometry (strips and 2 x 2 mm(2) square-meshed grids). The optimal experimental conditions for sintering were established and laser beam parameters (beam speed, BS, and power, P) were found for each blend composition. Morphology of sintered objects was analyzed by SEM and found to be dependent on the morphology of the sintered powders. Sintered samples were analyzed by chemical imaging (CI), FTIR-ATR, DSC, and contact angle analysis. No evidence of the occurrence of degradation phenomena was found by FTIR-ATR for sintered samples, whereas DSC parameters of PCL and blends showed changes which could be attributed to some molecular weight decrease of PCL during sintering. CI of sintered samples showed that the polysaccharide phase was homogeneously dispersed within the PCL matrix, with the only exception being the PCL/D blend. The contact angle analysis showed that all samples were hydrophilic. Fibroblasts were then seeded on scaffolds to evaluate the rate and the extent of cell adhesion and the effect of the polysaccharides (S, D, G) on the bioactivity of the PCL-based blends.

Physical - mechanical characterization of poly(lactide)/poly (ε-caprolactone) blends with ethyl ester L-lysine triisocyanate as reactive agent

Effect of Ethyl Ester L-Lysine Triisocyanate addition to produce reactive PLA/PCL bio-polyester blends for biomedical applications

Poly(L-Lactide) Materials with Balanced Mechanical Properties Prepared by Blending with Peg-Mb-Ppa Multiblock Copolymers

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Preparation and characterization of polyethylene glycol/poly(L-lactic acid) blends

A New Generation of Poly(lactide/ε-Caprolactone) Polymeric Biomaterials for Application in the Medical Field.

Rheology of Poly(lactic Acid)/poly(trimethylene Terephthalate) Blends Compatibilized by Clay or Maleic Anhydride-Grafted Poly(ethylene-Octene) Elastomer

Poly(lactic acid)/ poly(ε-caprolactone) blends: the effect of nanocalcium carbonate and glycidyl methacrylate on interfacial characteristics

Sustainable polylactide/polycaprolactone based polyurethane blends fabricated via reactive compatibilization

Preparation of high melt strength polypropylene by the reactive extrusion process and its foaming application

Use of crosslinking agent to produce high‐performance PLA/EVA blends via reactive processing

Poly(lactic acid)/poly(ε-caprolactone) blends: Separate effects of nanocalcium carbonate and glycidyl methacrylate on interfacial characteristics

Poly(ε-Caprolactone)/Poly(Lactic Acid) Blends Compatibilized by Peroxide Initiators: Comparison of Two Strategies

Blends of Poly-(ε-caprolactone) and Polysaccharides in Tissue Engineering Applications

Melt blending of poly(lactic acid) with biomedically relevant polyurethanes to improve mechanical performance

Improving the Toughness and Thermal Resistance of Polyoxymethylene/Poly(lactic acid) Blends: Evaluation of Structure-Properties Correlation for Reactive Processing

Synthesis of Poly(l-lactide-co-ε-caprolactone) Copolymer: Structure, Toughness, and Elasticity

Thermal, Mechanical and Degradation Properties of Flexible Poly (1,3-Trimethylene Carbonate)/poly (L-Lactide-co-ε-caprolactone) Blends

Synthesis, Characterization and Biocompatibility of Elastomeric Poly(L-co-D,L-lactic acid-co-Caprolactone)urethane for Biomedical Applications

Mechanical and thermal properties of conventional and microcellular injection molded poly (lactic acid)/poly (ε-caprolactone) blends

Interaction of Microstructure and Interfacial Adhesion on Impact Performance of Polylactide (PLA) Ternary Blends