Abstract:Voluntary hand movements are usually impaired after a cerebral stroke, affecting millions of people per year worldwide. Recently, the use of hand exoskeletons for assistance and motor rehabilitation has become increasingly widespread. This study presents a novel hand exoskeleton, designed to be low cost, wearable, easily adaptable and suitable for home use. Most of the components of the exoskeleton are 3D printed, allowing for easy replication, customization and maintenance at a low cost. A strongly underactuated mechanical system allows one to synergically move the four fingers by means of a single actuator through a rigid transmission, while the thumb is kept in an adduction or abduction position. The exoskeleton’s ability to extend a typical hypertonic paretic hand of stroke patients was firstly tested using the SimScape Multibody simulation environment; this helped in the choice of a proper electric actuator. Force-myography was used instead of the standard electromyography to voluntarily control the exoskeleton with more simplicity. The user can activate the flexion/extension of the exoskeleton by a weak contraction of two antagonist muscles. A symmetrical master–slave motion strategy (i.e., the paretic hand motion is activated by the healthy hand) is also available for patients with severe muscle atrophy. An inexpensive microcontroller board was used to implement the electronic control of the exoskeleton and provide feedback to the user. The entire exoskeleton including batteries can be worn on the patient’s arm. The ability to provide a fluid and safe grip, like that of a healthy hand, was verified through kinematic analyses obtained by processing high-framerate videos. The trajectories described by the phalanges of the natural and the exoskeleton finger were compared by means of cross-correlation coefficients; a similarity of about 80% was found. The time required for both closing and opening of the hand exoskeleton was about 0.9 s. A rigid cylindric handlebar containing a load cell measured an average power grasp force of 94.61 N, enough to assist the user in performing most of the activities of daily living. The exoskeleton can be used as an aid and to promote motor function recovery during patient’s neurorehabilitation therapy.

Conceptual design and virtual prototyping of a wearable upper limb exoskeleton for assisted operations

An Upper-Limb Power-Assist Exoskeleton Using Proportional Myoelectric Control

Design, Development, and Testing of an Intelligent Wearable Robotic Exoskeleton Prototype for Upper Limb Rehabilitation

Preliminary Testing of a Passive Exoskeleton Prototype Based on McKibben Muscles

Design and Implementation of a Rehabilitation Upper-limb Exoskeleton Robot Controlled by Cognitive and Physical Interfaces

Design and Analysis of Upper Limb Passive Exoskeleton Robot for Lift Assist

Bio-Inspired Conceptual Mechanical Design and Control of a New Human Upper Limb Exoskeleton

An Experimental Evaluation of the Proto-MATE: A Novel Ergonomic Upper-Limb Exoskeleton to Reduce Workers' Physical Strain

A Wearable Flexible Exoskeleton for Upper Limb Assistance

Optimal design of active-passive shoulder exoskeletons: a computational modeling of human-robot interaction

Design, Development, and Functional Validation of a 3D-Printed Passive Upper Limb Exoskeleton

A Completely Portable and Concealable, Lightweight Assistive Exosuit for Upper Limbs

A New Exoskeleton Prototype for Lower Limb Rehabilitation

On the design of an exoskeleton for neurorehabilitation: design rules and preliminary prototype

Design of a 3D-Printed Hand Exoskeleton Based on Force-Myography Control for Assistance and Rehabilitation

Structure design and analysis of upper limb wearable passive power-assisted exoskeleton robot

Design, Development, and Control of a Hand/Wrist Exoskeleton for Rehabilitation and Training

Development of an ergonomic wearable robotic device for assisting manual workers

A cable-driven exosuit for upper limbs: design, control, and evaluation

Design of a wearable shoulder exoskeleton robot with dual-purpose gravity compensation and a compliant misalignment compensation mechanism

Model-Based Comparison of Passive and Active Assistance Designs in an Occupational Upper Limb Exoskeleton for Overhead Lifting