Abstract:To explore the effects of cutting speed, feed rate and rake angle on chip morphology transition, a thermomechanical coupled orthogonal (2-D) finite element (FE) model is developed, and to determine the effects of tool nose radius and lead angle on hard turning process, an oblique (3-D) FE model is further proposed. Three one-factor simulations are conducted to determine the evolution of chip morphology with feed rate, rake angle, and cutting speed, respectively. The chip morphology evolution from continuous to saw-tooth chip is described by means of the variations of chip dimensional values, saw-tooth chip segmental degree and frequency. The results suggest that chip morphology transits from continuous to saw-tooth chip with increasing feed rate and cutting speed, and changing a tool’s positive rake angle to negative rake angle. There exists a critical cutting speed at which the chip morphology transfers from continuous to saw-tooth chip. The saw-tooth chip segmental frequency decreases as the feed rate and the tool negative rake angle value increases; however, it increases almost linearly with the cutting speed. The larger negative rake angle, the larger feed rate and higher cutting speed dominate saw-tooth chip morphology while positive rake angle, small feed rate and low cutting speed combine to determine continuous chip morphology. The 3-D FE model considers tool nose radii of 0.4 mm and 0.8 mm, respectively, with tool lead angels of 0 deg and 7 deg. The model successfully simulates 3-D saw-tooth chip morphology generated by periodic adiabatic shear and demonstrates the continuous and saw-tooth chip morphology, chip characteristic line and the material flow direction between chip-tool interfaces. The predicted chip morphology, cutting temperature, plastic strain distribution, and cutting forces agree well with the experimental data. The oblique cutting process simulation reveals that a bigger lead angle results in a severer chip deformation, the maximum temperature on the chip-tool interface reaches 1289 deg, close to the measured average temperature of 1100 deg; the predicted average tangential force is 150N, with 7% difference from the experimental data. When the cutting tool nose radius increases to 0.8 mm, the chip’s temperature and strain becomes relatively higher, and average tangential force increases 10N. This paper also discusses reasons for discrepancies between the experimental measured cutting force and that predicted by finite element simulation.

New Development in the Theory of the Metal-Cutting Process: Part II—The Theory of Chip Formation

Simulation of Chip Formation in High-Speed Hard Machining

The Finite Element Analysis Of Serrated Chip Formation In High-Speed Cuffing Auto Panel Dies

Study on the Effect of Tool Inclination Angle in Machining Process Based on Three-Dimensional Thermo-Elastic-Plastic Model

Mechanism of Saw-Tooth Chip Formation of Titanium Alloy Based on Finite Element Simulation

Simulation of 3d Chip Shaping of Aluminum Alloy 7075 in Milling Processes

Finite Element Simulation of Serrated Chip Formation in High-speed Milling of A lloy Cast Iron

Understanding The Deformation Of Metals In High Speed Cutting

Study of segmented chip formation in cutting of high-strength lightweight alloys

Theoretical Analysis of Serrated Chip Formation Based on Ideal Models in High Speed Cutting

Effect of cutting conditions on the serrated chip formation in high-speed cutting

On the Steady-State Workpiece Flow Mechanism and Force Prediction Considering Piled-Up Effect and Dead Metal Zone Formation

A Finite Element Study of Chip Formation Process in Orthogonal Machining

Predicting the Effects of Cutting Parameters and Tool Geometry on Hard Turning Process Using Finite Element Method

Research on the Ductile Chip Formation in Grinding of Brittle Materials

Predicting The Effects Of Rake Angle, Cutting Speed And Feed Rate On The Chip Morphology In Hard Turning

Experimental contribution to the study of the Ti6Al4V chip formation in orthogonal cutting on a milling machine

The Periodical Fluctuation of Residual Stress in Hard Turned Surface and Its Relationship with Chip Formation

Microstructure evolution modeling of Ti6Al4V alloy during cutting using the Particle Finite Element Method and homogeneous field distributions

ANALYTICAL CHIP FORMATION MODEL OF MICRO-END-MILLING

Study on the Formation Mechanism of Serrated Chips in the Cutting Process of Powder Metallurgy Superalloys Based on a Modified J–C Constitutive Relation Simulation Model