Abstract:We aim at developing hexavalent chromium-free coatings for frequently touched decorative parts. Cr(N,O) and multilayered CrN/CrO coatings were deposited by means of reactive magnetron sputtering. All samples presented good adhesion to the substrates enhanced by an epoxy layer designed to enhance PVD coating adhesion. Similar substrates are found in the automotive industry and can be used in appliances where a metallic finish is desired by the consumer. Corrosion behavior was induced, using artificial sweat to simulate long exposure to human touch for 96 h. In potentiodynamic polarization tests, the coatings were revealed to be nobler than the substrate alone. Cr displayed a non-existent passivation region, while gCrN exhibited a quick passivation of the surface and its respective breakdown and several current fluctuations, indicating the occurrence of pitting, which was confirmed by SEM micrography after the corrosion. Regarding EIS results, all films depicted a diminution of impedance modulus (|Z|) after 96 h, which indicates a diminution of corrosion resistance against artificial sweat. Nitride films exhibited the worst anticorrosive features. On the other hand, Cr and CrO exhibited the highest |Z| values. These results are corroborated by low the corrosion rates of both coatings. The equivalent electrical circuit allows us to confirm oxide formation in the outermost layer of the films due to electrolyte/surface interaction, indicating a self-protecting mechanism. Nitride films showed the lowest values and less corrosion resistance, confirming the results obtained in polarization potentiodynamic tests. The coatings developed in this work, namely Cr and CrO, showed a promising corrosion resistance behavior that could endure a lifetime of frequent human touch in various decorative applications either automotive or general appliances.

Corrosion Mechanism in Artificial Sweat Solution of In-Bearing White Bronze Alloy

Corrosion Assessment of Passivation Film Generated on Solder Surface in Artificial Sweat Solution

Mechanism of corrosion behavior between Pb-rich phase and Cu-rich structure of high Sn–Pb bronze alloy in neutral salt spray environment

Corrosion Behavior of Aluminum Bronze under Thin Electrolyte Layers Containing Artificial Seawater

Corrosion Behavior of Bronze under Organic Acid‐containing Thin Electrolyte Layer

Electrochemical Study Of The Corrosion Behavior Of Bronze Under Acetic Acid-Containing Thin Electrolyte Layers

Fabrication, Microstructure and Corrosive Behavior of Different Metallographic Tin-Leaded Bronze Alloys Part II: Chemical Corrosive Behavior and Patina of Tin-Leaded Bronze Alloys

Electrochemical corrosion behavior of bronze materials in an acid‐containing simulated atmospheric environment

Corrosion and Tarnish Behaviour of 925ag75cu and 925ag40cu35zn Alloys in Synthetic Sweat and H2S Atmosphere

Insight into the Mechanism of Alloying Elements (sn, Be) Effect on Copper Corrosion During Long-Term Degradation in Harsh Marine Environment

Effect of Sulphate on the Corrosion Behavior of Bronze under a Chloride‐containing Thin Electrolyte Layer

Corrosion Resistance in Artificial Perspiration of Cr-Based Decorative Coatings

Corrosion and corrosive-wear behaviors of a high strength and toughness Cu-15Ni-8Sn alloy in seawater

(Digital Presentation) Corrosion-Resistance Investigation of Titanium Passive Layer in Acidic Solution

Corrosion Behaviors of Electroless Plating Ni–P Coatings Deposited on Magnesium Alloys in Artificial Sweat Solution

Investigation on the Self-Lubricating Properties of Boronized Cocrfenimn High Entropy Alloy in Corrosive Environments

In-Situ Investigation of Atmospheric Corrosion Behavior of Bronze under Thin Electrolyte Layers Using Electrochemical Technique

Corrosion Behavior of Copper Bearing Steels and the Derived In-Situ Coating

Corrosion Behavior of Cu-Al Brazed Joints in the Salt Spray Environment

Micro-abrasion–corrosion Behaviour of a Biomedical Ti–25Nb–3Mo–3Zr–2Sn Alloy in Simulated Physiological Fluid