Abstract:ABSTRACTDeveloped more than 80 years ago, the design procedure of concrete filled steel tubes (CFST) has several limitations that can still be found in most current international design standards. The two main limitations that present themselves are the lack of ability to achieve material enhancement when using high strength materials and restrictions on the geometry of the steel tube thickness to the overall column diameter. This geometric limitation is placed on the design to ensure that the steel tube remains ‘compact’. In complying with these constraints it is assumed in the design equations that local buckling of the steel tube will not take place before the ultimate global buckling load is achieved.With the introduction of higher strength materials, specifically when dealing with steel, the strength increase leads to the design of sections with increased slenderness. As the section becomes more slender, the ability to maintain the compact section limitations in the design codes becomes increasingly difficult. This paper looks at an experimental study on very thin‐walled steel tubes filled with high‐strength concrete and how localised buckling affects their compressive capacity.Adopting a diameter to thickness ratio of 200, 24 circular tubes were constructed using a high‐strength cold‐formed steel sheet, with yield stresses above 500MPa and filled with 100MPa concrete. Employing both thin‐walled sections and high strength materials, the effects of localised buckling in these composite members when subjected to compression has been studied. The experimental programme explored four main conditions; when both the steel and concrete were loaded and bonded together, when the concrete core inside the CFST was loaded, when the steel tube in the CFST was loaded and when the concrete core without the steel tube was tested.By studying the failure modes of both the concrete and the steel tube when acting compositely and individually, the experimental work shows that there is valid evidence to support the theory that even when using high strength materials in slender sections, confinement to the concrete core is provided. Finally, the results of the experimental work have been compared to the compressive design capacities predicted by current international design codes, showing that these provisions are conservative.

Structural performance of geopolymer-concrete-filled steel tube members subjected to compression and bending

Compressive Behavior of Small-Diameter Concrete-Filled Fiber-Reinforced Polymer Tubes As Internal Reinforcements

Behavior of Hybrid FRP-Concrete-Steel Tubular Columns: Experimental and Theoretical Studies

Flexural behavior of concrete-filled circular steel tubes under high-strain rate impact loading

Axial Impact Behavior of Confined Concrete Filled Square Steel Tubes Using Fiber Reinforced Polymer

Experimental research on seismic behavior of concrete-filled reactive powder concrete tubular columns

Flexural strength analysis of non-post-tensioned and post-tensioned concrete-filled circular steel tubes

Experimental and Analytical Study of Hollow Section Concrete-Filled GFRP Tubes in Bending

Experimental Investigation and Analysis of Bond–Slip Behavior between Geopolymer Concrete and Steel Tube with Varying Structural Measures

Behavior of Cross Arms Inserted in Concrete-Filled Circular GFRP Tubular Columns

Experimental and numerical investigations on the bond-slip behavior of the interface between geopolymer concrete and steel tube

Experimental Investigation and Design of Hollow Section, Centrifugal Concrete-Filled GFRP Tube Columns

Numerical Study on Concrete Filled GFRP-Steel Tube under Cyclic Loading

Mechanical performance of glass fiber–reinforced polymer tubes filled with steel-reinforced high-strength concrete subjected to eccentric compression

08.17: Experimental Behaviour of High‐strength Thin‐walled Concrete Filled Steel Tubular Stub Columns

Performance of Circular Concrete-Filled FRP-Grooved Steel Composite Tube Columns under Axial Compression

Double-tube Concrete Columns with a High-Strength Internal Steel Tube: Concept and Behaviour under Axial Compression

Effective usage of high strength steel tubes: Axial compressive behavior of hybrid FRP-concrete-steel solid columns

Research on flexural performances on the CFRP confined concrete filled steel tube with square cross-section

Experimental Research on Concrete-Filled GFRP Tubes and GFRP-Steel Composite Tubes under Axial Compressive Load

Analysis Of Frp-Strengthened Concrete-Filled Steel Tubular Columns Under Axial Compression