Concentrating rare earth elements in brown coal humic acids by mechanochemical treatment

Tatiana Skripkina,Margarita Belokozenko,Svetlana Shatskaya,Vera Tikhova,Igor Lomovskiy

DOI: https://doi.org/10.1039/d1ra07228e

IF: 4.036

2021-01-01

RSC Advances

Abstract:Mechanochemical oxidation leads to concentration of rare earth elements in soluble humic acids fraction.

chemistry, multidisciplinary

What problem does this paper attempt to address?

Removal Mechanism of Mineral Impurities in Molybdenum Concentrate Treatment Process

Qihang Liu,Ruilin Liu,Shuangping Yang,Weiguo Feng,Miao Wang

DOI: https://doi.org/10.3390/min13010035

IF: 2.5

2022-01-01

Minerals

Abstract:The removal of impurities in molybdenum concentrate has become a new challenge for enterprises due to the cancellation of pickling. Whether impurity minerals can be converted into soluble ions during roasting is important for the impurity removal by current water washing. In this work, the interaction between various impurity elements in the treatment process of molybdenum concentrate was studied by process simulation experiments combined with X-ray fluorescence (XRF) and X-ray diffraction (XRD), inductively coupled plasma-optical emission spectrometer (ICP-OES), ion chromatography (IC), scanning electron microscope-energy dispersive spectrometry (SEM-EDS), the use of FactSage7.0 modeling and the mineral liberation analyzer (MLA). The results show that most of the impurity elements such as K, Si and Al exist in the form of alkaline minerals with large molecular weight. In the roasting process of molybdenum concentrate, K-containing minerals, such as muscovite and orthoclase, can be transformed into K+, Al3+ and other soluble ions, and then can be removed by water washing. Humidification increased the conversion degree of orthoclase to soluble ions, which was conducive to the removal of impurities by the washing process. The results of MLA microscopic analysis confirmed that impurities such as FeS2, CaSO4, SiO2, and especially FeS2, would form a high density mixture with MoO3 during the high temperature roasting process, and thus reduced the leaching rate of Mo. Therefore, the humidification and control of the molybdenum concentrate is an effective measure to remove impurities.
Mechanical Activation as a Stage of Coal Sample Preparation in the Analysis of Rare Earth Elements Content by Inductively Coupled Plasma Mass Spectrometry

Yudina Lidiya I.,Skripkina Tatiana S.,Shatskaya Svetlana S.

DOI: https://doi.org/10.2174/0115734110288231231229105645

2024-01-24

Current Analytical Chemistry

Abstract:Background: Brown coals are recognized as promising sources of rare earth elements (REEs). Rare earths are present in both the mineral and organic parts of brown coal. Objectives: This study was conducted to investigate the influence of preliminary mechanical activation in the process of sample preparation prior to analyzing the concentrations of rare earth elements in brown coal samples of various origins and compositions. Methods: Four coal samples from different deposits in Russia were selected for the study. Samples were treated with mechanical activation, without reagents, or mechanochemical activation, with humic acids added externally as reagents. X-ray phase analysis was carried out with the selected samples. The quantities of rare-earth elements present in the samples were studied by the method of high-sensitivity inductively coupled plasma mass spectrometry (ICP-MS). Results: It was found that the mechanical activation of coal before dissolution in a mixture of nitric and hydrofluoric acids leads to an increase in the determined concentration of rare earth elements. For this study, the expediency of using only nitric acid as an optimal solvent for the elemental analysis of coal samples was shown. The total concentration of all REE after dissolution of nitric acid and mechanochemical activation with humic acid reached 2456 g/t in Vanchin coal, 968 g/t in Azeysky coal, and 24 g/t and 150 g/t in Itatsky and Spetsugli coals, respectively. Conclusion: It was found that the mechanical activation of coal before dissolution in a mixture of nitric and hydrofluoric acids leads to an increase in the determined concentration of rare earth elements. For this study, the expediency of using only nitric acid as an optimal solvent for the elemental analysis of coal samples was shown. The total concentration of all REE after dissolution of nitric acid and mechanochemical activation with humic acid reached 2456 g/t in Vanchin coal, 968 g/t in Azeysky coal, and 24 g/t and 150 g/t in Itatsky and Spetsugli coals, respectively.

chemistry, analytical
Conversion of Weathered Coal into High Value-Added Humic Acid by Magnetically Recoverable Fe3O4/LaNiO3 Nanocatalysts under Solid-Phase Grinding Conditions

Manrong Song,Gang Wang,Yanli Suo,Zhiqiang Wu,Haijuan Zhan,Wanyi Liu

DOI: https://doi.org/10.3390/catal12040392

IF: 3.9

2022-03-31

Catalysts

Abstract:The Fe3O4/LaNiO3 composite, synthesised with the sol-gel method, is considered to be an excellent nanocatalyst for the production of high value-added humic acids from oxidised weathered coal under solid phase milling process conditions. Under optimum process conditions (1% catalyst, 10% activator, 60 min grinding), 48.4% of the weathered coal can be oxidised to produce humic acid. The prepared Fe3O4/LaNiO3 catalyst was characterized by HRTEM, XRD, and XPS, etc. The heterojunction structure that can promote the electron transfer between the components of the composite material was formed with the recombination of Fe3O4 and LaNiO3. The activation of surface oxygen species and adsorbed oxygen could be enhanced with the help of electron transfer between components. Compared to the blank sample or the LaNiO3 catalyst alone, the molecular weight of the humic acid produced using the Fe3O4/LaNiO3 composite catalyst was significantly lower (maximum heavy mean molecular weight decreased from 59.7 kDa to 5.5 kDa) and the number of reactive groups in humic acid increased (to seven times that of the blank sample). Oxygen-free vacuum experiments indicated that O2 has an indispensable effect on its excellent catalytic performance in the Fe3O4/LaNiO3 system. In addition, Fe3O4/LaNiO3 could be used at least six times by simple magnetic separation. The development and preparation of perovskite composite catalysts provide a promising approach to the environmentally friendly development and application of weathered coal, as well as an effective method to resolve the associated environmental pollution.

chemistry, physical
Investigating Physicochemical Methods to Recover Rare-Earth Elements from Appalachian Coals

Rachel Yesenchak,Scott Montross,Shikha Sharma

DOI: https://doi.org/10.3390/min14111106

IF: 2.5

2024-10-31

Minerals

Abstract:The demand for rare-earth elements is expected to grow due to their use in critical technologies, including those used for clean energy generation. There is growing interest in developing unconventional rare-earth element resources, such as coal and coal byproducts, to help secure domestic supplies of these elements. Within the U.S., Appalachian Basin coals are particularly enriched in rare-earth elements, but recovery of the elements is often impeded by a resistant aluminosilicate matrix. This study explores the use of calcination and sodium carbonate roasting pre-treatments combined with dilute acid leaching to recover rare-earth elements from Appalachian Basin coals and underclay. The results suggest that rare-earth element recovery after calcination is dependent on the original mineralogy of samples and that light rare-earth minerals may be more easily decomposed than heavy rare-earth minerals. Sodium carbonate roasting can enhance the recovery of both light and heavy rare-earth elements. Maximum recovery in this study, ranging from 70% to 84% of total rare-earth elements, was achieved using a combination of calcination and sodium carbonate roasting, followed by 0.25 M citric acid leaching.

geochemistry & geophysics,mineralogy,mining & mineral processing
Enhanced electrochemical treatment of humic acids and metal ions in leachate concentrate: Experimental and molecular mechanism investigations

Peng Hu,Huankai Li,Yunkai Tan,Adeyemi S Adeleye,Tianwei Hao

DOI: https://doi.org/10.1016/j.jhazmat.2023.132774

2024-01-15

Abstract:Membrane technologies are effective for treating leachate, but they generate leachate concentrates (LCs), which contain elevated humic acids (HAs) and metals. LCs are very challenging and expensive to treat; but in-situ coagulation-electrochemical oxidation (CO-EO) treatment is promising. We previously hypothesized and proved that substituting the widely used graphite cathode with an Al cathode will generate Al(OH)3 floccules that would enhance HAs removal in CO-EO systems. However, the fundamental mechanisms are unclear. Here, we examined this hypothesis using laboratory experiments (using an Al cathode and a Ti/Ti4O7 anode CO-EO system) and performed molecular dynamics (MD) simulation to investigate the underlying mechanisms. Up to 84.2% HAs was removed by the Al-cathode system, which is ∼10% higher than a graphite cathode-based system. Based on MD simulation we found that enhanced HAs removal occurred via two steps: (1) degradation by oxidants produced at the anode, and (2) subsequent coagulation with the Al(OH)3 generated from the Al cathode. This finding challenges the current belief that whole HAs and Al(OH)3 directly flocculate. Meanwhile, metal removal efficiency by the graphite cathode system was only 0.8-13.9%, which increased up to 13-folds at most when in the Al cathode system. This work provides new molecular-level insights into an efficient electrochemical treatment of LC.
Pretreatment of Bituminous Coal By-Products for the Hydrometallurgical Extraction of Rare Earth Elements

Tushar Gupta,Ahmad Nawab,Rick Honaker

DOI: https://doi.org/10.3390/min13050614

IF: 2.5

2023-04-29

Minerals

Abstract:Low-temperature plasma (LTP) oxidation has been widely used to study the mineralogy of the mineral matter existing in coal sources. The current study investigated the potential of LTP oxidation as a pre-treatment method to improve rare earth element (REE) leachability from coal and its by-products. Representative density-fractionated samples of Baker and Fire Clay coarse refuse seam materials were ground to a top size of 180 μm and subjected to low-temperature plasma oxidation. Subsequently, the treated samples were leached at 1% w/v solids concentration and 75 °C for 5 h using (i) de-ionized (DI) water, (ii) 0.1 mol/L of ammonium sulfate, and (iii) 1.2 mol/L of sulfuric acid. It was determined that LTP treatment improved REE leaching characteristics, especially the leaching of heavy REEs (HREE), existing in the lighter density fractions of the Baker seam coarse refuse material. For instance, the HREE recovery for the 1.6 specific gravity (SG) float fraction increased from 8% to 33% using 0.1 mol/L of ammonium sulfate solution after 32 h of LTP treatment. This finding indicated that HREEs associated with the organic matter were released by the LTP treatment and adsorbed onto the surfaces of highly negative charged mineral matter and was exchanged with ammonium to allow their recovery. Similarly, when using 1.2 mol/L of sulfuric acid, the HREE recovery increased from 23% to 53% for the 1.6 SG float fraction. Interestingly, LTP oxidation did not provide significant improvement in REE recovery from the 2.2 sink density fractions, which was likely due to its lower organic content. No significant benefits were observed when treating the Fire Clay coarse refuse material, which was likely due to the lack of organic affinity and the difficult-to-leach REE minerals associated with the coal source such as monazite, xenotime, and zircon. Conversely, high-temperature oxidation within a temperature range of 600–750 °C significantly improved REE leaching characteristics for both coal sources. Improvement in REE recovery was due to decarbonization of the material, clay dehydroxylation and subsequent conversion of liberated REE-bearing minerals into a more leachable form. However, increasing the temperature above 800 °C decreased REE recovery due to the conversion of meta-kaolinite into mullite, which is chemically stable.

geochemistry & geophysics,mineralogy,mining & mineral processing
Methods for obtaining humate-containing fertilizers from brown coal

Bekzhan Omarov,Kurmanbek Zhantassov,Manap Zhantassov,Kamilya Kirgizbayeva,Zhaxylyk Altybayev

DOI: https://doi.org/10.1080/19392699.2024.2330409

2024-03-16

International Journal of Coal Preparation and Utilization

Abstract:The purpose of the study is to examine the main methods of obtaining fertilizers and optimizing processes. Using methods of analysis, comparison, and experimentation, three main approaches to obtaining fertilizers were identified: grinding and mixing with potassium hydroxide (KOH), ultrafine grinding with chemical additives, and a complex method for processing caustobioliths. Comparative analysis of the investigated methods allowed for identifying their advantages, disadvantages, and effectiveness. The key result was the ability to determine the most effective method for producing humate-containing fertilizers from brown coal, depending on specific production conditions and requirements. The results of the study showed that the ultrafine grinding process with chemical additions, such as urea and alkali metal hydroxides, showed promising potential for creating highly effective humate-containing fertilizers from brown coal, in addition to the comparative analysis. After thorough optimization, this technique showed improved fertilizer utilization and superior plant uptake, making it a strong contender for sustainable farming methods. Nevertheless, achieving optimal results requires detailed process parameter optimization. The study underscores the importance of using brown coal in humate-containing fertilizer production as an environmentally safe and sustainable approach. The results can contribute to further development and improvement of humate-containing fertilizer production methods, promoting sustainable agriculture and increased crop productivity.

energy & fuels,mining & mineral processing
BEHAVIOR OF RARE-EARTH METALS IN HYDROMETALLURGICAL PROCESSING OF PYROCHLOR-MONAZITE-GOETHITE ORES

N. A. Permyakova,E. I. Lysakova,S. I. Anufrieva,E. G. Likhnikevich

DOI: https://doi.org/10.32362/24106593-2018-13-3-64-71

2018-06-28

Fine Chemical Technologies

Abstract:The article is dedicated to finding out the specific features of the behavior of rare-earth metals in hydrometallurgical processing of pyrochlore-monazite-goetite ores of the Chuktukonsky ore field is shown in the work. Chuktukonsky ore field is a potential source of rare earth metals. The mentioned ores are practically unenforceable. Hydrometallurgical methods for their complex processing were suggested. Agitational and autoclave nitric acid leaching depending on such technological parameters as temperature, HNO3 concentration, process duration, S:L ratio and the use of H2O2 were studied. The possibility of transferring manganese (that is present in a significant amount in the ore) into a nitric acid solution by hydrogen peroxide was considered. Based on the results of the conducted studies, the distribution of REM in the products of the hydrometallurgical conversion of pyrochlore-monazitegoetite ore was estimated. It was found out that incomplete opening of the ore material was observed during agitational leaching: average REM recovery into the solution is 60%. The study made it possible to solve the problem of purifying nitric acid solutions from phosphorus that hinders the subsequent extraction and separation of rare earth metal ions forming strong complexes with rare earths. Removal of phosphorus from the solution was achieved by conducting the process under pressure at elevated temperatures (200-230 0C). It was found that the optimal decomposition conditions ensuring the transfer of almost 99% of the REM into the nitric acid solution are: 25% solution of HNO3, ore size - 0.071 mm; 5% by volume H2O2; t(160 0С) = 1 h; t(230 0С) = 1 h, gradual temperature increase from 160 to 230 0С; S:L = 1:8. Autoclave nitric-acid leaching allows selecting rare earth metals from the main part of iron, phosphorus and niobium.

English Else
Process Condition Optimization and Structural Feature Analysis of Humic Acid Extraction from Weathered Lignite

Yan Yang,Yanhong Li,Yuanqin Zhang,Miao Wang,Pingyan Wang,Donghui Liu

DOI: https://doi.org/10.1021/acsomega.4c01840

IF: 4.1

2024-09-03

ACS Omega

Abstract:In this study, response surface methodology (RSM) was adopted to investigate the optimization of process conditions for extracting humic acid (HA) from coal, aiming to enhance the yield of humic acid. Additionally, UV-vis spectroscopy, FTIR, XRD, TG-DTG, CP/MAS13CNMR, XPS, and molecular fluorescence were utilized to examine the properties of HAs. The extraction time significantly influenced the yield from Lishi weathered lignite, while the liquid-solid ratio had a significant impact on the yield from Wuhai weathered lignite. The interactive effect between factors did not have a significant effect on the yield. The optimal extraction conditions for Lishi humic acid (LSHA) were determined to be an extraction time of 4.4 h, NaOH concentration of 0.30 mol/L, and liquid-solid ratio of 21 mL/g, while those for Wuhai humic acid (WHHA) were 3.1 h, 0.21 mol/L, and 12 mL/g, respectively. Under these optimal conditions, the true yield values closely matched the predicted value obtained from the model optimization. Comparative analysis of the HAs revealed similarities in their chemical properties, including the degree of aromaticity, molecular weight, and distribution of functional groups. The aromaticity of WHHA was higher compared to that of LSHA. The higher hydrophilic-hydrophobic index of LSHA contributed to its relatively high biological activity compared to that of WHHA. Both humic acids belong to terrestrial humic acids. The results of the study provide a reference for further application of humic acid.
Extraction and Chemical Characterization of Humic Acid from Nitric Acid Treated Lignite and Bituminous Coal Samples

Noureen Fatima,Asif Jamal,Zaixing Huang,Rabia Liaquat,Bashir Ahmad,Rizwan Haider,Muhammad Ishtiaq Ali,Tayyba Shoukat,Zeid A. ALOthman,Mohamed Ouladsmane,Tariq Ali,Shafqat Ali,Naseem Akhtar,Mika Sillanpää

DOI: https://doi.org/10.3390/su13168969

IF: 3.9

2021-08-11

Sustainability

Abstract:Currently, conversion of coal into alternative fuel and non-fuel valuable products is in demand and growing interest. In the present study, humic acid was extracted from two different ranks of coal, i.e., low rank and high rank (lignite and bituminous), through chemical pretreatment by nitric acid. Samples of lignite and bituminous coal were subjected to nitric acid oxidation followed by extraction using KOH and NaOH gravimetric techniques. The chemical pretreatment of both types of coal led to enhanced yields of humic acid from 21.15% to 57.8% for lignite low-rank coal and 11.6% to 49.6% bituminous high rank coal. The derived humic acid from native coal and nitric acid treated coal was analyzed using elemental analysis, E4/E6 ratio of absorbance at 465 nm and 665 nm using UV-Visible spectrophotometry and Fourier transformed infrared spectroscopy FTIR. The chemical characteristics of coal treated with nitric acid have shown increased molecular weight and improved aromaticity with more oxygen and nitrogen and lower C, H, and sulphur content. The E4/E6 ratio of nitric acid-treated low and high ranks of coal was high. The FTIR spectroscopic data of nitric acid-treated lignite coal indicates an intensive peak of carboxyl group at 2981.84 cm−1, while bituminous coal was shown in cooperation with the N-H group at 2923.04 cm−1. SEM was performed to detect the morphological changes that happen after producing humic acid from HNO3 treatment and native coal. The humic acid produced from HNO3 treated coal had shown clear morphological changes and some deformations on the surface. SEM-EDS detected the major elements, such as nitrogen, in treated humic acid that were absent in raw coal humic acid. Hence, the produced humic acid through HNO3 oxidation showed a more significant number of humic materials with improved efficiency as compared to native coal. This obtained humic acid can be made bioactive for agriculture purposes, i.e., for soil enrichment and improvement in growth conditions of plants and development of green energy solutions.

environmental sciences,environmental studies,green & sustainable science & technology
Extraction of Humic Acids from Lignite and Its Use as a Biochar Activator

Huijin Li,Shuang Ding,Jie Yuan

DOI: https://doi.org/10.1021/acsomega.2c08192

IF: 4.1

2023-03-24

ACS Omega

Abstract:Current research focuses on extracting humic acid (HA) compounds from low-rank coals to obtain high value-added products. In this study, HAs with high purity and low heavy metal content were obtained from lignite by combining acid pretreatment with hydrothermal treatment. Scanning electron microscopy, elemental analysis (EA), Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction, and inductively coupled plasma optical emission spectrometry (ICP-OES) were used to analyze raw lignite and HAs. The effects of acid and hydrothermal treatments on the inorganic elements, functional groups, and yield of HAs were examined. The results showed that acid treatment reduced the ash content of lignite from 20 to 9%, and hydrothermal treatment increased the yield of HAs from 36 to 68%. The chemical properties of HAs exhibited an increase in molecular weight and improved aromaticity after acid and hydrothermal treatments. The results of ICP-OES analysis suggested that the combined method of acid and hydrothermal treatments resulted in a significant reduction of heavy metal elements in HAs. FTIR analysis confirmed the results and demonstrated that the extracted HA from nitric acid pretreated and hydrothermal generation of lignite PHA was rich in carboxyl and phenolic functional groups. PHA was applied to biochar as an activator for the adsorption of heavy metal ions. The experimental results showed that PHA was successfully loaded onto biochar and introduced a large number of functional groups, and the adsorption capacity of the modified biochar for Pb2+ was effectively improved.
Study on NH3-SCR performance and mechanism of Fe/Mn modified rare earth concentrate

Yuze Bai,Jinhao Zhu,Huijuan Luo,Zhenfeng Wang,Zhijun Gong,Ran Zhao,Wenfei Wu,Kai Zhang

DOI: https://doi.org/10.1016/j.mcat.2021.111665

IF: 4.6

2021-09-01

Molecular Catalysis

Abstract:In this paper, the transition metals Fe and Mn are doped on the surface of rare earth concentrates by the impregnation method to prepare NH3-SCR catalyst active powder. SEM, XRD, BET, XPS, H2-TPR, NH3-TPD, NO-TPD, FTIR and other characterization methods are used to explore the surface properties and mechanism of rare earth concentrates doped with transition metals, and at the same time determine its catalysis in a simulated flue gas device performance. The results showed that the NOx conversion rate of Fe and Mn doped rare earth concentrates reached 94.8% at 200 °C. The specific surface area of the rare earth concentrate increases after Fe and Mn are doped. Fe and Mn are uniformly dispersed on the surface of the rare earth concentrate. The combined effect of Fe, Mn and the rare earth concentrate provides more weak acid sites for the reaction and promotes desorption of NO in the low temperature section. The redox performance of rare earth concentrates has also been greatly improved. Rare earth concentrates doped with Fe and Mn mainly follow the L-H mechanism in the low temperature section, and mainly follow the E-R mechanism in the high temperature section. In general, the introduction of transition metals Fe and Mn effectively improves the NH3-SCR catalytic activity of rare earth concentrates, and the rare earth concentrates themselves have good resistance and tolerance, which is useful for preparing NH3-SCR catalysts from natural minerals. It has important theoretical significance and practical value, and at the same time has a pioneering role in the application of Baiyun Obo rare earth minerals in industrial production.

chemistry, physical
From ash to oxides: Recovery of rare-earth elements as a step towards valorization of coal fly ash waste

Mohammed Dardona,Sanjay K. Mohanty,Matthew J. Allen,Timothy M. Dittrich

DOI: https://doi.org/10.1016/j.seppur.2023.123532

IF: 8.6

2023-03-15

Separation and Purification Technology

Abstract:Coal fly ash (CFA) is both a valuable waste material and a potential source of environmental contamination. The inclusion of metals such as rare-earth elements offer a possible incentive towards waste valorization if the metals can be extracted and recovered in an economical manner. Rare-earth elements (REEs) have many technological applications and are critically important in the manufacture of electric vehicles, communication devices, and industrial magnets. However, the global supply of rare-earth elements has faced shortages and price shocks. Current methods for separating and isolating individual rare-earth elements use large amounts of energy and organic solvents, raising concerns over environmental impacts. These factors have led to the investigation of nontraditional sources and separation techniques for these elements. We describe a column-based system that uses a newly developed ligand-associated organosilica sorbent to concentrate and separate rare-earth elements from fly ash leachate. The fly ash used in this study originally contained 0.024 wt% rare-earth elements and the final oxide powder after enrichment contained >10 wt% rare-earth elements, which is a enrichment of >400 times. This process requires no additional organic solvents after the sorbent media has been synthesized, offering an alternative to the current standard using solvent extraction for rare-earth element recovery.

engineering, chemical
Process Research and Mechanism Analysis of Pellet Roasting and Monazite Decomposition

Jianfei Li,Yubo Xu,Zhisheng Dong,Ruifeng Ma,Xiaowei Zhang,Ligang Wen,Qing Wang,Xiaoyan Hao,Wenbin Xin,Zhaogang Liu

DOI: https://doi.org/10.1134/s1067821224600121

2024-10-20

Russian Journal of Non-Ferrous Metals

Abstract:The concentrated sulfuric acid roasting method and caustic soda method, as the main processes for treating Bayan Obo mixed rare earth concentrate, have been operating normally for decades. However, due to their serious pollution, high cost, and waste of accompanying resources, relevant rare earth enterprises are facing severe environmental and cost pressures. The sodium carbonate roasting method is a clean method for treating rare earth minerals, but due to the phenomenon of "ring formation" in the rotary kiln during the reaction process, this process has not been widely promoted. Based on the above facts, this article proposes a decomposition method for sodium pelletizing to decompose monazite, which effectively alleviates the related technical problems caused by the "ring formation" problem. Moreover, the rare earth leaching rate is 86.87%, and the recovery rates of F, P, and Th are 98.64, 13.87, and 88.96%. It is a potential rare earth mineral cleaning production process and can provide certain technical references for relevant rare earth enterprises.

metallurgy & metallurgical engineering
Rare Earth Element Recovery and Hydrochar Evaluation from Hyperaccumulator by Acid Leaching and Microwave-Assisted Hydrothermal Carbonization

Shiyu Li,Bin Ji,Wencai Zhang

DOI: https://doi.org/10.3390/min14030277

IF: 2.5

2024-03-07

Minerals

Abstract:Phytomining is a sustainable approach that uses hyperaccumulators for critical element extraction from various substrates, such as contaminated soils, mine tailings, and aqueous solutions. In this study, grass seeds were fed with a solution containing Y, La, Ce, and Dy, resulting in around 510 mg/kg (dry basis) of total rare earth elements (TREEs) accumulated in grass leaves. Electron probe microanalyzer (EPMA) analysis showed that rare earth elements (REEs) in the grass leaves (GL) predominantly complexed with phosphorous (P). Around 95% of Y, 93% of La, 92% of Ce, and 93% of Dy were extracted from the GL using 0.5 mol/L H2SO4 at a solid concentration of 5 wt.%. Subsequently, microwave-assisted hydrothermal carbonization (MHTC) was used to convert the leaching residue into hydrochar to achieve a comprehensive utilization of GL biomass. The effect of temperature on the structural properties and chemical composition of the resulting hydrochar was evaluated. Scanning electron microscopy (SEM) analysis revealed that the original structure of GL was destroyed at 180 °C during MHTC, producing numerous microspheres and pores. As the reaction temperature increased, there was a concurrent increase in carbon content, a higher heating value (HHV), and energy densification, coupled with a decrease in the hydrogen and oxygen contents of hydrochar. The evolution of H/C and O/C ratios indicated that dehydration and decarboxylation occurred during MHTC. The results showed that the waste biomass of the GL after REE extraction can be effectively converted into energy-rich solid fuel and low-cost adsorbents via MHTC.

geochemistry & geophysics,mineralogy,mining & mineral processing
Magnetic coal gangue-based catalysts for peroxymonosulfate activation and benzo[ a ]pyrene degradation: The construction of Fe and N dual active sites

Chao Liang,Jiajia Wang,Chunquan Li,Wei Han,Yongming Song,Bin Li,Shuaijun Yin,Zhiming Sun

DOI: https://doi.org/10.1016/j.jece.2024.114613

IF: 7.7

2024-11-01

Journal of Environmental Chemical Engineering

Abstract:The magnetic coal gangue (CG)-based catalysts were successfully prepared by impregnation-calcination method with iron (Fe) and nitrogen (N) co-doping for peroxymonosulfate (PMS) activation, illustrating excellent catalytic property with 100.00 % removal rate of benzo[ a ]pyrene (BaP). Additionally, Fe/N co-doped CG catalysts (Fe-N-CG) possess desirable performance against co-existing anions and organic matter (HA), with a nearly 80.00 % removal rate in actual water systems. The mechanism of activating PMS and removing BaP was comprehensively analyzed through a series of characterizations and experiments, proving that the Fe and N double reaction sites could enhance the contribution of radical paths and non-radical paths for BaP degradation. Finally, the safety and prospects for practical environmental remediation via Fe-N-CG for PMS activation were further evaluated by ECOSAR toxicity analysis software and mung bean growth experiments. In summary, the development of Fe-N-CG widened the high-value utilization of CG and supplied a deep insight into the restoration of organically polluted environments.

engineering, chemical, environmental
Controllable synthesis of magnetic carbon composites with high porosity and strong acid resistance from hydrochar for efficient removal of organic pollutants: An overlooked influence

xiangdong zhu,feng qian,yuchen liu,daniel matera,gang wu,shicheng zhang,jianmin chen

DOI: https://doi.org/10.1016/j.carbon.2015.12.044

IF: 10.9

2016-01-01

Carbon

Abstract:Facile fabrication of magnetic carbon composites (MCs) via pyrolysis of hydrochar in the presence of ZnCl2 and an iron salt has been attracting enormous interest to simultaneously realize high-surface area and magnetization. During this synthesis, the interactions between the carbon matrix and iron salts have remained unknown. In this work, a closer look was taken on iron salt interactions and their respective effect on MC characteristics. These newly fabricated MCs can provide guidance for further design of efficient MCs. It was discovered that ferric chloride (FeCl3) promoted the enhancement of MC porosity, largely due to the strong reduction reaction between amorphous carbon and iron oxide (γ-Fe2O3 and Fe3O4). Various other iron salts (including ferrous oxalate (FeC2O4), ferric citrate (FeC6H5O7), and ferric sulfate (Fe2(SO4)3) were also evaluated. These compounds inhibited pore structure development, resulting from decreased carbonization seen in the composite. This phenomenon was observed from complexation reactions between Zn2+ and the corresponding anions of these salts. Also, high Fe content and low γ-Fe2O3:Fe3O4 ratios led to decreased acid resistance of the MC. Finally, higher porosity in resultant MCs resulted in larger adsorption capacity for organic pollutants (roxarsone). This study will aid in further optimization of MCs to ultimately maximum performance.
Combined approaches for comprehensive processing of rare earth metal ores

Vladimir I. Kuzmin,Gennady L. Pashkov,Victor G. Lomaev,Elena N. Voskresenskaya,Vera N. Kuzmina

DOI: https://doi.org/10.1016/j.hydromet.2012.06.011

IF: 4.217

2012-11-01

Hydrometallurgy

Abstract:Technologies for processing rare earth ores (Chuktukon deposits, East Siberia, Russia) have been developed. The ores are composed of iron-manganese oxides and contain 3–7% of rare-earth oxides in the phosphate form (turnerite, florencite) and 0.5–1% of niobium oxide (chalcolamprite). These ores are refractory and do not lend themselves to concentration, therefore various processes for their direct chemical processing have been considered. A number of investigations to estimate the technological behavior of the Tomtor and Chuktukon ores, and to develop various processes for their treatment, have been carried out. Two approaches for processing the Chuktukon ores have been suggested. The first one comprises extraction of the rare earth metals and production of a niobium concentrate; the second one provides a method for processing the complex ores resulting in the production of rare earth metals, iron and manganese alloys.

metallurgy & metallurgical engineering
Carbothermal reduction followed by sulfuric acid leaching of Bayan Obo tailings for selective concentration of iron and rare earth metals

Yan Zhou,Jianxing Liu,Gongjin Cheng,Xiangxin Xue,He Yang

DOI: https://doi.org/10.1016/j.seppur.2021.118742

IF: 8.6

2021-09-01

Separation and Purification Technology

Abstract:In this work, carbothermal reduction followed by sulfuric acid (H2SO4) leaching of Bayan Obo tailings has been studied for the selective concentration of Fe and rare earth (RE) minerals. The effect of basicity on the metallization rate of Fe, transfer behaviors of metallic Fe and RE elements, phase composition, and element migration was investigated using XRD, SEM-EDS, EDS mapping, and FT-IR spectroscopy. At a roasting temperature of 1100–1200 °C and a basicity of 1.87, more than 99% of Fe was metallized and 97.91% of Fe and 94.94% of RE were separated magnetically. After roasting, the RE elements mainly existed in Ca2RE8(SiO4)6O2 and Ca8RE2(PO4)6O2, 88% of which were leached out by H2SO4 at 25 °C with an initial concentration of 2 mol/L and a stirring speed of 900 r/min. The precipitation of RE2(SO4)3 was responsible for the incomplete recovery of RE elements during leaching.

engineering, chemical
Co-Thermal Oxidation of Lignite and Rice Straw for Synthetization of Composite Humic Substances: Parametric Optimization via Response Surface Methodology

Yanling Li,Xi Chen,Zhen Zhuo,Xueqin Li,Tanglei Sun,Peng Liu,Tingzhou Lei

DOI: https://doi.org/10.3390/ijerph192416875

IF: 4.614

2022-12-15

International Journal of Environmental Research and Public Health

Abstract:In this study, Baoqing lignite (BL) and rice straw (RS), which were the representatives of low-rank coal and biomass, were co-thermally oxidized to produce composite humic substances (HS), including humic acid (HA) and fulvic acid (FA). Taking HS content as the output response, the co-thermally oxidizing conditions were optimized through single factor experiment and response surface methodology (RSM). The structures of HA and FA prepared under optimized conditions were analyzed by SEM, UV, and FTIR. Results showed that HS content was clearly influenced by the material ratio, oxidation time, and oxidation temperature, as well as their interactions. The optimized co-thermal oxidization condition was as follows: BL and RS pretreated with a material ratio of 0.53, oxidation time of 59.50 min, and oxidation temperature of 75.63 °C. Through verification, the experimental value (62.37%) had a small relative error compared to the predicted value (62.27%), which indicated that the developed models were fit and accurate. The obtained HA had a tightly packed block structure; FA had a loosely spherical shape. The molecular weight of FA was 2487 Da and HA was 20,904 Da; both had a smaller molecular weight than that reported in other literature. FA showed strong bands at 1720 cm−1, thus confirming the presence of more oxygen-containing functional groups. The appearance of double peaks at 2900~2980 cm−1 indicated that HA contains more aliphatic chains. The co-thermal oxidation of BL and RS gives a new method for the synthesis of HS, and the optimization of co-thermal oxidation conditions will provide fundamental information for the industrialization of composite HS.

public, environmental & occupational health,environmental sciences

Concentrating rare earth elements in brown coal humic acids by mechanochemical treatment

Removal Mechanism of Mineral Impurities in Molybdenum Concentrate Treatment Process

Mechanical Activation as a Stage of Coal Sample Preparation in the Analysis of Rare Earth Elements Content by Inductively Coupled Plasma Mass Spectrometry

Conversion of Weathered Coal into High Value-Added Humic Acid by Magnetically Recoverable Fe3O4/LaNiO3 Nanocatalysts under Solid-Phase Grinding Conditions

Investigating Physicochemical Methods to Recover Rare-Earth Elements from Appalachian Coals

Enhanced electrochemical treatment of humic acids and metal ions in leachate concentrate: Experimental and molecular mechanism investigations

Pretreatment of Bituminous Coal By-Products for the Hydrometallurgical Extraction of Rare Earth Elements

Methods for obtaining humate-containing fertilizers from brown coal

BEHAVIOR OF RARE-EARTH METALS IN HYDROMETALLURGICAL PROCESSING OF PYROCHLOR-MONAZITE-GOETHITE ORES

Process Condition Optimization and Structural Feature Analysis of Humic Acid Extraction from Weathered Lignite

Extraction and Chemical Characterization of Humic Acid from Nitric Acid Treated Lignite and Bituminous Coal Samples

Extraction of Humic Acids from Lignite and Its Use as a Biochar Activator

Study on NH3-SCR performance and mechanism of Fe/Mn modified rare earth concentrate

From ash to oxides: Recovery of rare-earth elements as a step towards valorization of coal fly ash waste

Process Research and Mechanism Analysis of Pellet Roasting and Monazite Decomposition

Rare Earth Element Recovery and Hydrochar Evaluation from Hyperaccumulator by Acid Leaching and Microwave-Assisted Hydrothermal Carbonization

Magnetic coal gangue-based catalysts for peroxymonosulfate activation and benzo[ a ]pyrene degradation: The construction of Fe and N dual active sites

Controllable synthesis of magnetic carbon composites with high porosity and strong acid resistance from hydrochar for efficient removal of organic pollutants: An overlooked influence

Combined approaches for comprehensive processing of rare earth metal ores

Carbothermal reduction followed by sulfuric acid leaching of Bayan Obo tailings for selective concentration of iron and rare earth metals

Co-Thermal Oxidation of Lignite and Rice Straw for Synthetization of Composite Humic Substances: Parametric Optimization via Response Surface Methodology