Abstract:The fuel consumption of an engine is an essential parameter that needs to be measured during the testing of an agricultural machinery. Commercially available fuel meters are expensive. The purpose of the study is to develop a fuel meter with data logging capabilities using inexpensive materials. The developed fuel meter follows the gravimetric principle in which the initial and final weights of the fuel after a specified amount time has elapsed are obtained and used to calculate the fuel consumption. The main components were the Arduino UNO microcontroller, data logging shield, and a load cell sensor. It was calibrated for diesel and gasoline fuels during the actual testing of different agricultural machinery such as centrifugal pumps, small engines, two-wheel tractors, and four-wheel tractors. Data were compared to the existing fuel meter and calibration curves were generated. Separate tanks were used for both the gasoline and diesel fuel to avoid mixing of fuels and damaging the engine. The generated equations for diesel fuel (y = 1.0957x – 0.0962) and for gasoline fuel (y = 0.8551x – 0.0017) were implemented in the Arduino code. A paired T-test was conducted and it showed that at a 5% level of significance, there is no significant variation in the data before calibration (p= 0.054) and after calibration (p= 0.550) for diesel fuel. While at a 5% level of significance, there is a significant variation in the data before calibration (p=1.03e-8 ) for gasoline fuel but showed no significant variation after calibration (p=0.610). In comparison to the existing fuel meter (Ono Sokki FX-1100 Series), the percent difference obtained before calibration ranges from 1.05% to 27.12%, and after calibration ranges from 0% to 6.39% for diesel fuel. The percent difference obtained before calibration ranges from 10.18% to 19.96% and 2.03% to 9.40% after calibration for gasoline fuel in comparison to the volumetric method fuel meter of AMTEC. After performing calibration and statistical analysis, the developed fuel meter can be considered as good as the existing fuel meters of AMTEC. The researchers recommend to provide dampers to isolate the vibration that affects weight measurement during testing or use a different sensor like an inline flow sensor to eliminate this problem. The inline flow sensor also allows the design of the fuel meter to be simpler and it will be easier to transport and use during field testing of agricultural machinery. An inline flow sensor with a wide range of capacity would be applicable for testing of agricultural machinery

Analysis Methodology of Unusable Fuel Supply for Large Rotorcraft Airworthiness Certificate

Investigating the Potential of Parallel Hybrid-Electric Retrofit of Narrow-Body Airliner for Emission Reduction

System Level Study of Light Sport Aircraft with Conventional and Unconventional Propulsion Systems

Computational Tool for Aircraft Fuel System Analysis

An Engine-Level Safety Assessment Approach of Sustainable Aviation Fuel Based on a Multi-Fidelity Aerodynamic Model

Optimization of Fuel Injection Control System of Two-Stroke Aeroengine of UAV

Investigation on the Performance Characteristics of 2-Stroke Heavy Fuel Light Aeroengine (2SHFLA) with Different Fuel Injection Systems: Modeling and Comparative Simulation

Fuel Flowrate Control for Aeroengine and Fuel Thermal Management for Airborne System of Aircraft—An Overview

Orthogonal Reference Surrogate Fuels for Operability Testing

Novel custom-made design and analysis of hydrogen PEM fuel cell for high endurance small UAV applications

Experimental Study on a Liquid Hydrogen Tank for Unmanned Aerial Vehicle Applications

Crashworthiness of a Composite Bladder Fuel Tank for a Tilt Rotor Aircraft

Assessing the drag implications of hydrogen fuel utilization in small aircraft: a preliminary numerical analysis

Analysis of Aircraft Fuel Thermal Management System Under Different Architectures

Methodological Aspects of Assessing the Thermal Load on Diesel Engine Parts for Operation on Alternative Fuel

Data-driven real-time fuel cetane estimation and control design for multifuel UAVs

Advanced Sizing Methodology for a Multi-Mode eVTOL UAV Powered by a Hydrogen Fuel Cell and Battery

Performance degradation detection method of aeroengine fuel metering device

Design methodology and simulation analysis of hybrid fuel cell and battery systems for powering unmanned aircraft systems

Design and Development of a Low-Cost Fuel Consumption Meter for the Performance Testing of Agricultural Machinery

Aviation fuel pump health state assessment based on evidential reasoning and random forests