Abstract:Composite hydrogels of polyacrylamide-graft-polyaniline possessing both good mechanical strength and excellent electrical conductivity were prepared through a two-step polymerization route. Firstly, acrylamide (Am) and N-(4-aminophenyl) acrylamide (APAm) were radically copolymerized through Co-60 gamma-irradiated initiation in aqueous solution to form P (Am-co-APAm) hydrogels, of which the aminophenyl side groups facilitated the following graft polymerization of aniline. Secondly, after the lyophilized P (Am-co-APAm) hydrogels were re-swelled in aniline aqueous solution, aniline absorbed in the macroporous hydrogels underwent the oxidation coupling graft polymerization with aminophenyl side groups of P (Am-co-APAm) to result in P(Am-co-APAm)-g-PANI composite hydrogels. As expected, the produced polyaniline was naturally deposited onto the pore wall of P (Am-co-APAm) hydrogels, leading to the formation of inter-connected conductive pathway. Fourier transfer infrared spectroscopy, combined with the repeated removal of possible homopolyaniline with N-methylpyrilidone, confirmed the successful grafting. To modulating the mechanical properties, the influences of radical polymerization parameters were investigated. By changing radiation duration and dose rate, it was found that the gel fraction (GF) of P (Am-co-APAm) hydrogels increased with the increment of irradiation dose, while swelling degree (SD) had the maximum value under medium irradiation dose,reflecting that both monomer conversion and crosslinking degree affected the GF and SD of P (Am-coAPAm) hydrogels. With the increase in monomer concentration, GF was kept going up and levelled off at 1. 5 c(o) while SD kept going down and levelled off at the same monomer concentration. The tensile strength and elongation at break of P (Am-co-APAm) hydrogels decreased, but elastic modulus increased, reflecting the cooperative impact of crosslinking degree and polymer produced. Interestingly, as observed by scanning electron microscopy,the hydrogels prepared in neutral water had the open and macro-porous morphology while those obtained in HC1 solution had no distinct pores. For both hydrogels, TEM images showed no separated polyaniline particles located in the hydrogel pores and the thickness of pore wall obviously increased, indicating the formation of continuous polyaniline layer on the previous pore wall. Therefore, after being doped with HC1, P(Am-co-APAm)-g-PANI composite hydrogels exhibited excellent conductivity as high as 7 similar to 10 S/cm, which exceeded most of the reported values for polyaniline-containing hydrogels.

Enhanced swelling and mechanical properties of P(AM-co-SMA) semi-IPN composite hydrogels by impregnation with PANI and MWNTs-COOH

Interpenetrating Polymer Network Hydrogels Composed of Chitosan and Photocrosslinkable Gelatin with Enhanced Mechanical Properties for Tissue Engineering

Stretchable, Conductive PAni-PAAm-GOCS Hydrogels with Excellent Mechanical Strength, Strain Sensitivity and Skin Affinity

Enhancement and mechanism of mechanical properties and functionalities of polyacrylamide/polyacrylic acid hydrogels by 1D and 2D nanocarbon

Preparation and Investigation of Conductive Hydrogels of Polyacrylamide-g-Polyaniline

Functional Materials Made by Combining Hydrogels (Cross-Linked Polyacrylamides) and Conducting Polymers (Polyanilines)-A Critical Review

Tough Supramolecular Hydrogels with Excellent Self-Recovery Behavior Mediated by Metal-Coordination Interaction

High Performance Photopolymerized Poly (vinyl alcohol)/Silica Nanocomposite Hydrogels with Enhanced Cell Adhesion.

Strong, self-healing, shape memory PAA-PANI/PVA/PDA/AOP conductive hydrogels with interpenetrating network and hydrogen bond interaction

Carbon Nanotubes and Silica@polyaniline Core-Shell Particles Synergistically Enhance the Toughness and Electrical Conductivity in Hydrophobic Associated Hydrogels.

Polyacrylamide (Paam)/Nano-Zno Hybrid Hydrogels: Preparation And Properties

In situ polymerization approach to cellulose–polyacrylamide interpenetrating network hydrogel with high strength and pH-responsive properties

Strengthening Network of Polyacrylic Acid/Silica Nanocomposite Hydrogels

Thermoresponsive nanocomposite hydrogels with high mechanical strength and toughness based on a dual crosslinking strategy

Carboxymethyl cellulose-based semi-IPN hydrogel nanocomposite with improved physicochemical and mechanical properties

Poly(N-isopropylacrylamide)-Based Thermoresponsive Composite Hydrogels for Biomedical Applications

Mechanically Robust Polyacrylamide Composite Hydrogel Achieved by Integrating Lamellar Montmorillonite and Chitosan Microcrystalline Structure into Covalently Cross-linked Network

Preparation, properties, and drug release of thermo- and pH-sensitive poly((2-dimethylamino)ethyl methacrylate)/poly( N , N -diethylacrylamide) semi-IPN hydrogels

Synthesis and Properties of Thermo- and Ph-Sensitive Poly(diallyldimethylammonium Chloride)/poly(n,n-Diethylacrylamide) Semi-Ipn Hydrogel

Preparation and Characterization of Low‐Voltage Responsive Nanocomposite Shape‐Changing Hydrogels/Carbon Nanofibers With Enhanced Mechanical Properties

Boron nitride microfiber reinforced polyacrylic acid hydrogels with excellent self-adhesion, fast pH response, and strain sensitivity