Abstract:This research examines the potential of a synthetic e-diesel and oxymethylene dimethyl ether blend in a heavy-duty single-cylinder engine. The main purpose is to find the optimal engine settings that maximize engine efficiency and minimize emissions. As the first step, a methodology was developed and applied to simplify the engine's map into five characteristic points to be representative of the World Harmonized Transient Cycle, assigning weights to each load region. This simplification reported low error estimations for fuel consumption and NOx emissions over the cycle. After obtaining the five points, a drop-in analysis was assessed, where the fuel was evaluated with the same settings as diesel, revealing more advanced and shorter combustion with great reductions in soot emissions. Then, a group of three air management and three injection parameters was selected for optimization. A novel methodology combining Taguchi Design and Response Surface Methodology is developed and applied to find the best engine settings. By integrating these two methods, the research reduced the number of required experiments if only one method were used and maintained the goal of achieving higher thermal efficiencies with the new fuel blend compared to the diesel baseline. Significant statistical results were obtained in the Taguchi design, revealing the air management factors that most affected the responses; meanwhile, second-order models with high accuracy helped in finding the best injection parameters. Subsequently, the best settings were experimentally evaluated, and optimal conditions determined by the two methods were validated, confirming the effectiveness of the methodology. Optimization results revealed an improvement of around 2% higher efficiencies for the five tested points while achieving important average reductions of 28% less in NOx with additional decreases in CO, HC, and soot levels, all outperforming traditional diesel benchmarks. Finally, a well-to-wheel analysis using the simplified cycle confirmed a substantial reduction in carbon impact when replacing diesel with this alternative fuel. The successful application of this methodology to recalibrate an engine with an alternative fuel blend shows the potential of using these fuels in existing engines and offers a novel methodology that can be escalated and applied under the engine calibration context.

Adapting an Internal Combustion Engine to Oxy-Fuel Combustion With In-Situ Oxygen Production

An Experimental Study of the Combustion Process in a Natural-Gas Spark-Ignition Engine

Simulation and Experiment for Oxygen-enriched Combustion Engine Using Liquid Oxygen to Solidify CO 2

Numerical simulations and experiments of oxygen-enriched combustion in engine and using liquid oxygen to solidify carbon

Experimental and numerical investigation of methane combustion in a HCCI engine under enriched oxygen conditions

Optimizing compression ignition engine performance and emissions with onboard oxygen concentrator: an experimental study

Optimization methodology combining Taguchi design and response surface method to maximize a compression ignition engine efficiency fueled with oxygenated synthetic fuel

Applications of Oxyhydrogen, Direct Water Injection, and Early-Intake Valve Closure Technologies on a Petrol Spark Ignition Engine—A Path towards Zero-Emission Hydrogen Internal Combustion Engines

The Application of Argon-Oxygen Atmosphere to Investigate the Formation and Evolution of Fuel Nitrogen Oxides During the Oxidation of Hydrogen-Ammonia Fuel Mixtures under Representative Engine In-Cylinder Conditions

Evaluation of hydrogen injection and oxygen enrichment strategies in an ammonia-hydrogen dual-fuel engine under high compression ratio

Gas Oxy Combustion and Conversion Technologies for Low Carbon Energy: Fundamentals, Modeling and Reactors

Effect of boundary on homogeneous charge compression ignition engine fueled with anode off-gas and refueled anode off-gas

Virtual Development of a Single-Cylinder Hydrogen Opposed Piston Engine

Multi-objective optimization of a compression ignition engine using on-board methanol reforming

Kinetics Study of a Staged Combustor Concept for Oxy-Fuel Combustion Gas Turbine Cycles

Carbon Utilization Through Power to Gas and Oxyfuel Combustion Hybridization with Recycled CO2: Design and Preliminary Results

High-Performance Hydrogen-Fueled Internal Combustion Engines: Feasibility Study and Optimization via 1D-CFD Modeling

Assessment of environmentally friendly fuel emissions from in-use vehicle exhaust: low-blend iso-stoichiometric GEM mixture as example

A renewable clean energy application: Oxyhydrogen negative pressure inhalation for enhancing the combustion and emission characteristics of isopropanol/gasoline dual-fuel combined injection engine

On-board thermochemical energy recovery technology for low carbon clean gasoline direct injection engine powered vehicles

Experimental investigation of hydrogen combustion in a single cylinder PFI engine