Abstract:The development of friction stir welding (FSW) created the basic foundation for friction stir processing (FSP). This process entails refining the local microstructure and achieving the localised plastic deformation due to the stirring effect of the tool, which may involve adding additional filler material as required. The rotating tool involved in the process has a shoulder and pin responsible for heat generation for plastic deformation and localised mixing. The rotating tool is inserted and traversed on the desired surface, tailoring the material properties. The tool's exposure to the surface causes localised plastic deformation and thermal gradient, and microstructural changes occur locally. The present investigation uses Friction Stir Processing (FSP) to fabricate an aluminium metal matrix composite. Recently, the use of aluminium alloy has been replaced by composites because of their increased mechanical and physical properties (specific properties). The experiment leads to manufacturing an aluminium metal matrix composite using aluminium oxide, boron carbide and commercially pure copper dust. Later, the effect of heat treatment on the respective metal matrix composite is studied. A comparative study among three different types of FSP techniques viz. FSP, Reinforced FSP, and Heat-treated Reinforced FSP have been performed. The tool revolution speed (RPM) and tool traverse speed of 400 RPM and 10 mm/min had been implemented, respectively. The T4 Heat-Treatment cycle was used during the current investigation. This investigative study was performed to analyse the changes in grain sizes and hardness values at the stir zone (SZ), thermo-mechanically affected zone (TMAZ), heat affected zone (HAZ) and on the base materials (BM) of the samples. The reinforced FSP metal matrix composite (MMC) showed an 81.26% increase in the micro-hardness value (HV) compared to the base metal. Further on analysing the microstructures, the reinforced FSP composite showed a 65.20% reduction in grain size. Moreover, the Heat-Treated sample showed an increase in the micro-hardness value by 99.8%.

Recent development in friction stir processing of aluminum alloys: Microstructure evolution, mechanical properties, wear and corrosion behaviors

Mechanical, wear and corrosion behaviors of AZ91/SiC composite layer fabricated by friction stir vibration processing

Investigation on microstructure, mechanical and tribological properties of friction stir processing of AZ31/AlFeCrMoNb surface composite

A comparative study between friction stir processing and friction stir vibration processing to develop magnesium surface nanocomposites

Effect of vibration on mechanical and tribological characteristics during friction stir processed FeAlCrMoNb high entropy alloys particle reinforced AZ 31 Mg alloy

Achieving high mechanical and wear properties in the AZ31/(CeO2+ZrO2)p surface composite using friction stir processing: Application of vibration

Fabrication of in Situ Carbon Fiber/aluminum Composites Via Friction Stir Processing: Evaluation of Microstructural, Mechanical and Tribological Behaviors

Improvement in corrosion resistance of 5083 aluminum alloy via friction stir processing

Recent Advances in Friction Stir Welding/Processing of Aluminum Alloys: Microstructural Evolution and Mechanical Properties

Advancements in Aluminum-Based Composite Manufacturing: Leveraging ZrO2 Reinforcement through Friction Stir Process

Effect of Friction Stir Processing with B4C Particles on the Microstructure and Mechanical Properties of 6061 Aluminum Alloy

Effect of processing environment during friction stir processing of AZ31/(ZrO 2 +CuO)p surface composite on the mechanical and tribological performance

Friction Stir Spot Vibration Welding: Improving the Microstructure and Mechanical Properties of Al5083 Joint

Microstructural Evolution & Mechanical Properties of ZrO2/GNP and B4C/GNP reinforced AA6061 Friction Stir Processed Surface Composites - A Comparative study

Optimizing friction stir processing parameters for aluminium alloy 2024 reinforced with SiC particles: A taguchi approach of investigation

Comparative study of microstructural evolution and mechanical properties in friction stir processed, reinforced friction stir processed, and heat-treated reinforced friction stir processed Al composites

Influence of friction stir processing on microstructure and mechanical properties of AA6061 reinforced with Zr and Ni metallic particles

Effects of different cooling conditions on friction stir processing of A356 alloy: Numerical modeling and experiment

Mechanical properties and corrosion behavior of a friction stir processed magnesium alloy composite AZ31B–SiC

Effect of multi-pass friction stir processing on microstructure and mechanical properties of cast Al-7Fe-5Ni alloy

Energy Consumption and Tool Condition in Friction Stir Processing of Aluminum Alloys