Abstract:The present work investigates the effect of vanadium (V) micro-alloying addition on the microstructural evolution and mechanical properties of Al 354.0 alloy in as-cast and T6 condition. In particular, Al 354.0 with and without 0.3 wt.% V was developed by squeeze casting technique. The as-cast ingots were subjected to two types of heat treatment schedules, i.e., solution heat treatment at 495 °C for 8 h, followed by rapid water quenching and artificial aging at 190 °C for 2 h (T6), and solution heat treatment at 515 °C for 10 h, followed by rapid water quenching and artificial aging at 210 °C for 6 h (MT6), to modify the microstructure, morphology, and distribution of Al-, Cu-, and Mg-containing secondary phase(s). The phase and microstructure of unmodified and 0.3 wt.% V-modified alloys were analyzed using x-ray diffraction, optical microscopy, and field emission scanning electron microscopy coupled with energy-dispersive x-ray spectroscopy. Detailed analyses show that Al 2 Cu/Al 2 Cu(SiMg), Al 5 Si 2 Mg, and Al 2 Si were the strengthening phases in the unmodified alloy, whereas 0.3 wt.% V-modified alloy contains Al 10 V/Al 10 V(Mg), Al 3 Cu, Mg 2 Si, Al 4 Si, and Al(SiCuMg) as the primary strengthening phase(s). A subtle increase in the mechanical properties was evident in the 0.3 wt.% V-modified alloy compared to unmodified alloy at ambient temperature due to the presence of Al 10 V/Al 10 V(Mg) fine precipitates and Al(SiCuMg) intermetallic along the grain boundaries (GBs) preventing dislocation movement. T6 treatment resulted in a grain growth where needle/plate morphology of eutectic silicon was partially converted into spheroidal morphology, and Al 2 Cu/AlSiCuMg, Mg 2 Si, and Al 10 V/Al 10 V(Mg) intermetallic phases emerged increasing the tensile (0.3% V modified vs. unmodified; YS: ~ 287 vs. ~ 268 MPa, UTS: ~ 330 vs. ~ 334 MPa, elongation: ~ 1.5% vs. ~ 2.6%), compression (0.3% V modified vs. unmodified YS: ~ 497 vs. ~ 460 MPa, UCS: ~ 790 vs. ~ 776 MPa, compressive strain: ~ 40% vs. ~ 42%), and wear properties. However, modified T6 treatment (MT6) resulted in a grain growth where needle/plate morphology of eutectic silicon converted into spheroidal morphology, and Al 2 Cu partially and Mg 2 Si precipitates along the GBs were completely dissolved in the α -Al matrix by incipient melting improving the ductility (~5.9%) at the expense of yield strength (~104 MPa) and ultimate tensile strength (~218 MPa).

Consolidation and fabrication of vanadium and vanadium-base alloys

MA-SPS-HIP Technique for Vanadium Alloys Preparation

Processing of vanadium: a review

Preparation of high purity vanadium

Vanadium: A U.S. Perspective on an Understudied Metal

Effect of Vanadium Micro-alloying on the Microstructure and Mechanical Properties of Stir Cast Al 354.0 Alloy

A critical review on extraction and refining of vanadium metal

Blistering Behavior and Deuterium Retention in Tungsten Vanadium Alloys Exposed to Deuterium Plasma in the Linear Plasma Device STEP

Influence of Vanadium Precursor Powder Size on Microstructures and Properties of W–V Alloy

Application of Different Vanadium Alloys in Steel

Thermodynamic Study of Production of Vanadium–Nitrogen Alloy and Carbon Monoxide by Reduction and Nitriding of Vanadium Oxide

Study of Technological Properties and Processing Feasibility for Various Types of Vanadium Raw Materials in Russia

Hot deformation behavior of commercial pure vanadium

Mechanical behaviour of vanadium microalloyed steel under control environment compression

Nano-Structured Vanadium: Processing and Mechanical Properties under Quasi-Static and Dynamic Compression

Effects of vanadium content on the microstructure and tensile properties of NbTiV x Zr high-entropy alloys

The extraction of vanadium from titanomagnetites and other sources

A Review on Vanadium Extraction Techniques from Major Vanadium-Containing Resources

Review of leaching, separation and recovery of vanadium from roasted products of vanadium slag

The effect of vanadium on the microstructure and mechanical properties of TiAl alloy fabricated by twin-wire directed energy deposition-arc

Study of the influence of vanadium and niobium on the structure of Ti-Al-V and Ti-Al-Nb alloys formed by selective electron beam alloying