Observations of urban boundary layer structure during a strong urban heat island event

J. F. Barlow,C. H. Halios,S. E. Lane,C. R. Wood

DOI: https://doi.org/10.1007/s10652-014-9335-6

2014-02-16

Environmental Fluid Mechanics

Abstract:It has long been known that the urban surface energy balance is different to that of a rural surface, and that heating of the urban surface after sunset gives rise to the Urban Heat Island (UHI). Less well known is how flow and turbulence structure above the urban surface are changed during different phases of the urban boundary layer (UBL). This paper presents new observations above both an urban and rural surface and investigates how much UBL structure deviates from classical behaviour. A 5-day, low wind, cloudless, high pressure period over London, UK, was chosen for analysis, during which there was a strong UHI. Boundary layer evolution for both sites was determined by the diurnal cycle in sensible heat flux, with an extended decay period of approximately 4 h for the convective UBL. This is referred to as the “Urban Convective Island” as the surrounding rural area was already stable at this time. Mixing height magnitude depended on the combination of regional temperature profiles and surface temperature. Given the daytime UHI intensity of 1.5∘C$$1.5\,^\circ \mathrm{C}$$, combined with multiple inversions in the temperature profile, urban and rural mixing heights underwent opposite trends over the period, resulting in a factor of three height difference by the fifth day. Nocturnal jets undergoing inertial oscillations were observed aloft in the urban wind profile as soon as the rural boundary layer became stable: clear jet maxima over the urban surface only emerged once the UBL had become stable. This was due to mixing during the Urban Convective Island reducing shear. Analysis of turbulent moments (variance, skewness and kurtosis) showed “upside-down” boundary layer characteristics on some mornings during initial rapid growth of the convective UBL. During the “Urban Convective Island” phase, turbulence structure still resembled a classical convective boundary layer but with some influence from shear aloft, depending on jet strength. These results demonstrate that appropriate choice of Doppler lidar scan patterns can give detailed profiles of UBL flow. Insights drawn from the observations have implications for accuracy of boundary conditions when simulating urban flow and dispersion, as the UBL is clearly the result of processes driven not only by local surface conditions but also regional atmospheric structure.

mechanics,environmental sciences,water resources,oceanography,meteorology & atmospheric sciences

What problem does this paper attempt to address?

The problem that this paper attempts to solve is to explore how the urban boundary layer (UBL) structure differs from the classical behavior during urban heat island (UHI) events, especially the changes in the flow and turbulence structures between the urban and rural surfaces. Specifically, the research focuses on the following aspects:

1. **Differences in urban and rural boundary layer structures**: By conducting simultaneous observations in London (urban area) and Chilbolton (rural area), researchers attempt to determine the changes in urban and rural boundary layer structures at different stability stages, especially at night after the urban heat island effect reaches its peak.

2. **Urban convective island phenomenon**: The study found that in urban areas, even after sunset, due to the continuous heating of the urban surface, the urban boundary layer remains in a convective state, while the surrounding rural areas have become stable. This phenomenon is called the "Urban Convective Island". Researchers explored the impact of this phenomenon on the nocturnal wind speed profile, especially the formation and development of the nocturnal jet.

3. **Changes in turbulence characteristics**: Researchers analyzed the moments of turbulence (variance, skewness, and kurtosis) and found that on some mornings, the turbulence characteristics of the urban boundary layer showed "inverted" properties, that is, they showed different characteristics from the classical theory during the initial rapid growth of the convective urban boundary layer.

4. **Trends in mixing height changes**: Researchers found that due to the urban heat island intensity of about 1.5°C during the day, combined with multiple inversion layers in the temperature profile, the mixing heights in urban and rural areas showed opposite trends during the study period, ultimately resulting in a three - fold difference in mixing height by the fifth day.

Through these studies, the paper aims to provide a deeper understanding of the urban boundary layer structure and its evolution, which is of great significance for simulating the flow and diffusion processes in urban areas, because the urban boundary layer is not only affected by local surface conditions but also driven by the regional atmospheric structure.