Abstract:Rain erosion damage, caused by repeated droplet impact on wind turbine blades, is a major cause for concern, even more so at offshore locations with larger blades and higher tip speeds. Due to the negative economic influence of blade erosion, all wind turbine Original Equipment Manufacturers (OEMs) are actively seeking solutions. In most cases, since the surface coating plays a decisive role in the blade manufacture and overall performance, it has been identified as an area where a solution may be obtained. In this research, two main coating technologies have been considered: In-mould coatings (Gel coating) applied during moulding on the entire blade surface and the post-mould coatings specifically developed for Leading Edge Protection (LEP). The coating adhesion and erosion is affected by the shock waves created by the collapsing water droplets on impact. The stress waves are reflected and transmitted to the laminate substrate, so microstructural discontinuities in coating layers and interfaces play a key role on its degradation and may accelerate erosion by delamination. Analytical and numerical models are commonly used to relate lifetime prediction and to identify suitable coating and composite substrate combinations based on their potential stress reduction on the interface. Nevertheless, in order to use them, it is necessary to measure the contact adhesion resistance of the multi-layered system interfaces. The rain erosion performance is assessed using an accelerated testing technique, whereby the test material is repeatedly impacted at high speed with water droplets in a Whirling Arm Rain Erosion Rig (WARER). The materials, specifically the coating-laminate interphase region and acoustic properties, are further characterised by several laboratory tests, including Differential Scanning Calorimetry (DSC), pull-off testing, peeling-adhesion testing and nanoindentation testing. This body of work includes a number of case studies. The first case study compares two of the main coating technologies used in industry (i.e., gel coating and LEP); the second case investigates the effects of the in-mould gel coating curing; and the third considers the inclusion of a primer layer on a LEP configuration system. Following these case studies, the LEP is found to be a far superior coating due to its appropriate mechanical and acoustic properties and the interface between the coating and the substrate is highlighted as a key aspect, as poor adhesion can lead to delamination and, ultimately, premature failure of the coating.

Performance Investigation of Non-Linear Insulator against Surface Tracking on Wind Turbine Blade Surface

Investigation on Surface Degradation of Wind Turbine Blades Surface Using Modified Surface Tracking Test as Part of Lightning Protection Improvement

Evaluation of an AlSi-polyester abradable seal coating performance using high-temperature and high-velocity abrasion tests

Mitigation of Electrical Stresses on Outdoor Polymeric Insulator Using Nano-Zinc Oxide Coating: Simulation and Experimental Validation

Tracking, Erosion and Thermal Distribution of Micro‐aln + Nano‐sio 2 Co‐filled Silicone Rubber for High‐voltage Outdoor Insulation

Comparative AC Tracking and Erosion Resistance of Micro-A1n and BN Filled Silicone Rubber Composites

Thermal Analysis and Tracking Process in Hybrid Composites of Silicone Rubber

Circle Tests of Tracking and Erosion of the Composite Insulator

Effects of Nano-Sio2 Doping on Tracking Growth and Thermal Accumulation in Silicone Rubber Insulation

Investigation of Surface Degradation of Aged High Temperature Vulcanized (HTV) Silicone Rubber Insulators

Study on Surface Characteristics of E-glass Fiber Reinforced Epoxy Resin Composites in Different Stages of Tracking

Performance analysis of wind turbine blades using E-Glass fiber and SiO2- Al2O3-TiO2 MMT nanocomposite with AW 106 epoxy

Effect of Ageing on the Tracking Characteristics of High-Temperature Vulcanized Silicone Rubber Hybrid Composites for High Voltage Insulation

Surface Tracking of MgO/Epoxy Nanocomposites: Effect of Surface Hydrophobicity

Surface Structural Changes in Silicone Rubber Due to Electrical Tracking

Erosion Resistance of Micro-Aln and Nano-Sio2 Hybrid Filled Silicone Rubber Composites

On the Material Characterisation of Wind Turbine Blade Coatings: The Effect of Interphase Coating-Laminate Adhesion on Rain Erosion Performance

Study on Durability and Dynamic Deicing Performance of Elastomeric Coatings on Wind Turbine Blades

Preparation and performance study of SiO2 aerogel thermal insulation coating with nanoporous structure for wind turbine blade surface

Surface treatment of large-area epoxy resin by water-perforated metal plate electrodes dielectric barrier discharge: Hydrophobic modification and uniformity improvement

Investigation on Dry Band Arcing Induced Tracking Failure on Nanocomposites of EPDM Matrix