Abstract:This study demonstrates that the incorporation of the multifunctional ionic liquid 1‐allyl‐3‐methylimidazolium dicyanamide into multicomponent perovskite films significantly improves the efficiency and stability of solar cells through precise surface potential homogenization. This strategy achieves an ultra‐high power conversion efficiency of 20.44% for wide‐bandgap devices (1.81 eV) and increases the efficiency of conventional bandgap devices (1.53 eV) to 25.41%. The synthesis of multicomponent metal halide perovskites (MHPs) by cationic and/or halide alloying allows band gap tuning, optimizing performance and improving stability. However, these multicomponent materials often suffer from compositional, structural, and property inhomogeneities, leading to uneven carrier transport and significant non‐radiative recombination losses in lead halide perovskites. While many researchers have focused on the aggregation of perovskite halide ions, the impact of the surface potential has received relatively less attention. In this study, the multifunctional ionic liquid 1‐allyl‐3‐methylimidazole dicyanamide (AMI) is introduced into the perovskite precursor to effectively regulate the surface potential of the perovskite layer. This approach inhibits non‐radiative recombination, enhances carrier injection, and improves device performance. Surface potential homogenization within the perovskite layer leads to simultaneous improvements in both the efficiency and stability of perovskite solar cells. For wide‐bandgap perovskites (1.81 eV), the optimal power conversion efficiency (PCE) reaches 20.44%, with an open‐circuit voltage (Voc) of 1.339 V, a short‐circuit current density (Jsc) of 17.92 mA cm−2, and a high fill factor (FF) of 85%. This strategy also proved effective for conventional bandgap perovskite solar cells (PSCs) (1.53 eV), leading to a significant increase in performance, with the PCE increasing from 23.22% to 25.41%.

Stabilizing the Efficiency Beyond 20% with a Mixed Cation Perovskite Solar Cell Fabricated in Ambient Air under Controlled Humidity

Comprehensive Understanding of Heat-Induced Degradation of Triple-Cation Mixed Halide Perovskite for a Robust Solar Cell

Toward high efficiency for long-term stable Cesium doped hybrid perovskite solar cells via effective light management strategy

Application of Cesium on the Restriction of Precursor Crystallization for Highly Reproducible Perovskite Solar Cells Exceeding 20% Efficiency

Stabilizing γ‐CsPbI 3 Perovskite via Phenylethylammonium for Efficient Solar Cells with Open‐Circuit Voltage over 1.3 V

High-performance quasi-2D perovskite solar cells with power conversion efficiency over 20% fabricated in humidity-controlled ambient air

Ionic Liquid Stabilized Perovskite Solar Modules with Power Conversion Efficiency Exceeding 20%

Surface Potential Homogenization Improves Perovskite Solar Cell Performance

Air-processed and Mixed-Cation Single Crystal Engineering-Based Perovskite Films for Efficient and Air-Stable Perovskite Solar Cells

Simple Method of Dual Passivation with Efficiency Beyond 20% for Fabricating Perovskite Solar Cells in the Full Ambient Air

One-stone-for-two-birds strategy to attain beyond 25% perovskite solar cells

Phase transition induced recrystallization and low surface potential barrier leading to 10.91%-efficient CsPbBr3 perovskite solar cells

Surface Reconstruction for Efficient and Stable Monolithic Perovskite/Silicon Tandem Solar Cells with Greatly Suppressed Residual Strain

Advances in cesium lead iodide perovskite solar cells: Processing science matters

Highly Efficient and Stable Perovskite Solar Cells via Modification of Energy Levels at the Perovskite/Carbon Electrode Interface

Achieving Long‐Term Operational Stability of Perovskite Solar Cells with a Stabilized Efficiency Exceeding 20% after 1000 h

Combination of Hybrid CVD and Cation Exchange for Upscaling Cs-Substituted Mixed Cation Perovskite Solar Cells with High Efficiency and Stability

Holistic Strategies Lead to Enhanced Efficiency and Stability of Hybrid Chemical Vapor Deposition Based Perovskite Solar Cells and Modules

Achieving stable and high-efficiency (>21%) lead halide perovskite solar cells with δ-CsPbI2Br seed–assisted growth strategy

Ambient Air Processed Inverted Inorganic Perovskite Solar Cells with over 21% Efficiency Enabled by Multifunctional Ethacridine Lactate

Improving Crystallization and Stability of Perovskite Solar Cells Using a Low-Temperature Treated A-Site Cation Solution in the Sequential Deposition