Abstract:In order to overcome the drag at hypersonic speed, hypersonic flight vehicles require a high level of integration between the airframe and the propulsion system. Propulsion system based on scramjet engine needs a close interaction between its aerodynamics and stability. Hypersonic vehicle nozzles which are responsible for generating most of the thrust generally are fused with the vehicle afterbody influencing the thrust efficiency and vehicle stability. Single expansion ramp nozzles (SERN) produce enough thrust necessary to hypersonic flight and are the subject of analysis of this work. Flow expansion within a nozzle is naturally 3D phenomena; however, the use of side walls controls the expansion approximating it to a 2D flow confined. An experimental study of nozzle performance traditionally uses the stagnation conditions and the area ratio of the diverging section of the tunnel for approaching the combustor exit conditions. In this work, a complete hypersonic vehicle based on scramjet propulsion is installed in the test section of a hypersonic shock tunnel. Therefore, the SERN inlet conditions are the real conditions from the combustor exit. The performance of a SERN is evaluated experimentally under real conditions obtained from the combustor exit. To quantify the SERN performance parameters such as thrust, axial thrust coefficient C f x and lift L are investigated and evaluated. The generated thrust was determined from both static and pitot pressure measurements considering the installation of side walls to approximate 2D flow. Measurements obtained by a rake show that the flow at the nozzle exit is not symmetric. Pitot and pressure measurements inside the combustion chamber show nonuniform flow condition as expected due to side wall compression and boundary layer. The total axial thrust for the nozzle obtained with the side wall is slightly higher than without it. Static pressure measurements at the centerline of the nozzle show that the residence time of the flow in the expansion section is short enough and the flow of the central region of the nozzle is not altered by the lateral expansion when nozzle configuration does not include side walls.

THE EFFECTS OF BASE BLEED AND SUSTAINER ROCKET NOZZLE DIAMETER AND LOCATION ON THE BASE DRAG OF A BODY OF REVOLUTION WITH CONCENTRIC BOOST AND SUSTAINER ROCKET NOZZLES

Effect of Ramp Geometry on Single Expansion Ramp Nozzle Performance Characteristics

A Three-Dimensional Numerical Investigation on Drag Reduction of a Supersonic Spherical Body with an Opposing Jet

Effect of Bluff Body Attributes on Afterburner Combustion Characteristics of a Boron Solid Rocket Scramjet

Influence of Rarefaction Degree and Aft-Body Geometry on Supersonic Flows

Numerical Study of a Boundary Layer Bleedfor a Rocket-Based Combined-Cycle Inlet in Ejector Mode

The Effect of Leading Edge Bluntness on Scramjet Performance

Experimental Study of Single Expansion Ramp Nozzle Performance Using Pitot Pressure and Static Pressure Measurements

Prediction of Drag Coefficient of a Base Bleed Artillery Projectile at Supersonic Mach number

Effect of Bypass Duct on the Thrust Vectoring Performance of Dual Throat Nozzle in a Supersonic Aircraft

Performance Characterization of Single Expansion Ramp Nozzle at Hypersonic Mach Number

Numerical Investigation on the Effect of Fuel-Rich Degree in the RBCC Engine under the Ejector Mode

Numerical analysis of hydraulic properties of bionic nozzles and structural optimization based on CFD–FEA

Effect of counterflow argon plasma jet on aerodynamic drag of a blunt body at hypersonic Mach numbers

Analysis of Jet Blast Distance of a Refined Engine Nozzle Model for Departing Aircraft

Effects of blowing and suction jets on the aerodynamic performance of wind turbine airfoil

Study on the Nozzle of the Rocket Assisted Engine of BB/Rocket HE Shell

Combustion Behavior of Supersonic Jet for Single‐Flow Postcombustion Oxygen Lance with Various Secondary Nozzle Parameters

Drag reduction characteristics of recirculation flow at rocket base in an RBCC engine under ramjet/scramjet mode

Experimental Study on the Coupled Flow Field and Thrust Characteristics of Tail Cavity and Jet

Experimental Study of the Endwall Heat Transfer of a Transonic Nozzle Guide Vane with Upstream Jet Purge Cooling Part 1—effect of Density Ratio