Abstract:A comprehensive modeling framework for the thermoforming of polymer matrix woven laminate composite was developed. Two numerical indicators, the slip path length and traction magnitude, have been identified to be positively correlated to matrix smearing and wrinkling defects. The material model has been calibrated with picture-frame experimental results, and the prediction accuracy for intra-ply shear and thickness distribution was examined with measurements of the physically formed parts. Specifically, thickness prediction for most locations on the formed parts was accurate within an 11.6% error margin. However, at two points with significant intra-ply shear, the prediction errors increased to around 20%. Finally, a parametric study was conducted to determine the relationship between various process parameters and the quality of the formed part. For the trapezoidal part, orienting the laminate at 45 degrees to the mold axis reduces the likelihood of matrix smear and wrinkling defects. Although this laminate orientation yielded a greater spatial variation in part thickness, the thickness deviation is lower than that for the 0-degree orientation case. Two forming analyses were conducted with ramp rates of 25 mm/s and 80 mm/s to match the equipment's operational limits. It was observed that higher forming rates led to a greater likelihood of defects, as evidenced by a 15% and 10% increase in the formed part areas with longer slip paths and higher traction magnitudes, respectively. It was discovered that shallower molds benefit from faster ramp rates, while deeper molds require slower rates to manage extensive shearing, stretching and bending. Faster forming rates lead to smaller thickness increases at high intra-ply shear regions, indicating a shift from intra-ply shear to out-of-plane bending due to the visco-plastic effect of the molten laminate and can negatively impact part quality. Lastly, it was shown that a well-conceived strategy using darts could improve the part quality by reducing the magnitude of the defect indicators.

On the relevance of modeling viscoelastic bending behavior in finite element forming simulation of continuously fiber reinforced thermoplastics

Modelling approach for anisotropic inter-ply slippage in finite element forming simulation of thermoplastic UD-tapes

A viscoelastic–viscoplastic modeling approach for amorphous polymers in vacuum forming simulation

A 2D modeling approach for fluid propagation during FE-forming simulation of continuously reinforced composites in wet compression moulding

A Phenomenological Intra-Laminar Plasticity Model for FRP Composite Materials

Experimental Characterization and Numerical Modelling of Bending Behavior of Carbon Fiber Unidirectional Thermoset Prepregs

Numerical Implementation of Strain Rate Dependent Thermo Viscoelastic Constitutive Relation to Simulate the Mechanical Behavior of PMMA

A method for validation of finite element forming simulation on basis of a pointwise comparison of distance and curvature

Injection molding simulation of short fiber reinforced thermosets with anisotropic and non-Newtonian flow behavior

A Modeling Framework for the Thermoforming of Carbon Fiber Reinforced Thermoplastic Composites

Temperature-Dependent modelling of tension, in-Plane shear, and bending behaviour in non-isothermal thermo-Stamping process simulation of unidirectional UHMWPE fibre reinforced thermoplastic TPU composites

Finite strain anisotropic elasto-plastic model for the simulation of the forming and testing of metal/short fiber reinforced polymer clinch joints at room temperature

Experimental characterisation and constitutive modelling of the intra-ply tensile and shear properties of unidirectional fibre reinforced thermoplastics (UD FRTPs) under solid-state stamp forming conditions

Thermomechanical Modeling of Amorphous Glassy Polymer Undergoing Large Viscoplastic Deformation: 3-Points Bending and Gas-Blow Forming

Research on Anisotropic Viscoelastic Constitutive Model of Compression Molding for CFRP

Finite Element Simulation of the Viscoelastic Behavior of Elastomers under Finite Deformation with Consideration of Nonlinear Material Viscosity

Viscous and Thermal Modelling of Thermoplastic Composites Forming Process

Modeling of Texture Development during Metal Forming Using Finite Element Visco-Plastic Self-Consistent Model

Modeling of fiber‐bending stiffness in fiber‐reinforced composites with a dynamic mixed finite element method based on the principle of virtual power

Micromechanical Modeling of Viscoplastic Behavior of Laminated Polymer Composites with Thermal Residual Stress Effect

A Lamination Model for Forming Simulation of Woven Fabric Reinforced Thermoplastic Prepregs