Abstract:International Journal of Engine Research, Ahead of Print. Two-Stroke (2S) Compression Ignition (CI) engines have been used in aviation since World War II, for their excellent fuel efficiency and lightweight construction. In a modern light aircraft, these advantages still remain, along with the capability to run on jet fuel instead of gasoline. However, the design of these engines must be deeply revised, in order to incorporate the recent technologies, and it must be optimized with the support of CAE tools. The paper presents a CFD optimization of a turbocharged 2S CI 5.6 L flat-six aircraft engine developed by CMD. The scavenging system is of the Uniflow type, with exhaust poppet valves and a set of piston-controlled ports along the cylinder liner. Two mechanical superchargers are serially connected to the turbochargers. The crankshaft can be directly coupled to the propeller, thanks to its excellent balance and the relatively low maximum engine speed (2600 rpm). Differently from previous papers published on the same engine, the current study is focused on two crucial design topics: the optimization of the supercharging system and of the injection strategy. A customized version of KIVA-3V is used for the 3D-CFD cylinder analyses, while a commercial 1D-CFD code is employed to model the whole engine. The study is supported by a comprehensive experimental campaign, that permitted the accurate calibration of the numerical models. In comparison to any Four-Stroke delivering the same maximum power (400 HP at 2600 rpm, sea level), the analyzed engine is very light (about 220 kg), and efficient (211 g/kWh at typical cruise conditions). Despite the high performance, peak cylinder pressure and turbine inlet temperature at sea level are relatively low: 125 bar, 850 K. At rated power (360 HP@2400 rpm, sea level) combustion is complete and smoke-less, thanks to the optimization of the injection strategy, supported by the previous CFD analysis. The engine can operate at altitudes as high as 5500 m (18,000 feet), still delivering 270 HP at 2400 rpm, without relevant reduction of fuel efficiency. The key for the performance at high altitudes is the choice of the turbocharger considering the compressor choke limit easly reachable at high altitudes.

Simulation Modeling and Optimization of Uniflow Scavenging System Parameters on Opposed-Piston Two-Stroke Engines

Simulation Modeling Method and Experimental Investigation on the Uniflow Scavenging System of an Opposed-Piston Folded-Cranktrain Diesel Engine

Research on the Intake Port of a Uniflow Scavenging GDI Opposed-Piston Two-Stroke Engine

Conceptual Design and Optimization of Scramjet Engines Using the Exergy Method

Opposed-Piston Two-Stroke Diesel Engine Scavenging System Structural Optimization Based on GA-SVM

Experimental study of the impact of scavenging efficiency on diesel combustion in an opposed-piston two-stroke engine

Scavenging Ports’ Optimal Design of a Two-Stroke Small Aeroengine Based on the Benson/Bradham Model

Influence of the Port Height to Stroke Ratio on the Performance of an OP2S Engine Fueled with Methanol/Diesel

Evaluation of the Effect of Variable Compression Ratios Performance on Opposed Piston 2-Stroke Engine

Study of Scavenging and Combustion Processes for Small Two-Stroke Aviation Heavy Fuel Direct Injection Engines

Numerical optimization of supercharging and combustion on a two-stroke compression ignition aircraft engine

Composite Intake Ports Interference Mechanism and Application in Dual Intake Channels of the Opposed-Piston Diesel Engine

Simulation about the Effect of the Height-to-Stroke Ratios of Ports on Power and Emissions in an OP2S Engine Using Diesel/Methanol Blends

Simulation on the scavenging process of the opposite two-stroke diesel engine

Simulation and Experimental Research on a Mixed Pulse Converter Turbocharging System

Split-Spray Piston Geometry Optimized for HSDI Diesel Engine Combustion

Optimization of Gasoline Engine Intake System Based on 1D, 3D and Coupled Simulations

Model based mapping of a novel prototype spark ignition opposed-piston engine

Effect Of Piston Crevices On The Numerical Simulation Of A Heavy-Duty Diesel Engine Retrofitted To Natural-Gas Spark-Ignition Operation

Numerical analysis of mixing and combustion characteristics of a lateral swirl combustion system in OP2S diesel engines

Digital twin-driven optimization of gas exchange system of 2-stroke heavy fuel aircraft engine