Abstract:Purpose. To show the effectiveness of various methods of heat treatment of the studied steels with heating in ITI, as a result of which their mechanical properties are increased, which is due to the acquisition of a multiphase structure, one of the components of which in some cases is metastable austenite. Research methods. Steels 14Г2, 20ГЛ, 20ГФЛ 45Г were investigated. Various types of heat treatment were carried out with heating in the intercritical temperature interval. In the studied steels, a multiphase structure dispersed in chemical composition was obtained. Durometric, metallographic and X-ray research methods were used. Mechanical properties under tension and impact toughness were determined. These properties were compared with those obtained from the studied steels after typical heat treatment. Obtained results. It is shown that in the investigated steels, when performing various methods of heat treatment, there is no need to obtain a single-phase austenite structure, which is homogeneous in terms of its chemical composition, during heating. The creation of a multiphase dispersed micro-inhomogeneous structure in the studied steels by heat treatment methods, which include regulated heating and holding in ITI, allows to obtain after normalization, hardening and high or low tempering, as well as isothermal tempering, a good combination of strength and plastic properties, the level of which exceeds that obtained after the usual process. Scientific novelty. The paper considers an alternative point of view, according to which to improve the mechanical and service properties of steels, it is necessary to obtain multiphase dispersed micro-inhomogeneous structures in them, consisting of martensite, bainite, ferrite, carbides, carbonitrides and metastable residual austenite, as well as their various combinations. In order to obtain such structures, it is advisable to use heating and holding in ITI during the heat treatment of pre-eutectoid steels, in which austenite is formed, along with ferrite and carbides. At the same time, austenite has chemical micro-heterogeneity, because the carbon concentration at its boundary with carbide is significantly higher than at the boundary with ferrite. This makes it possible to obtain a multiphase dispersed micro-inhomogeneous structure after heat treatment. Practical value. Increasing the mechanical properties of steels makes it possible to increase the operational stability of machine parts, which is an important task of materials science. One of the directions of its solution is to obtain a multiphase structure in steels, one of the components of which is metastable austenite, in which the dynamic deformation martensitic transformation (DSMT) and the effect of self-hardening under load (SHL) occur under load. Methods of heat treatment with heating at ITI are easily implemented in production conditions and allow for energy savings. Modes of their implementation should be chosen taking into account obtaining the necessary properties, the initial structure, its defects and the cross-section of the products.

Processing and characterization of high strength dual-phase steel by two-step intercritical heat treatment process

On the use of thermomechanical processing to enhance the strength-ductility-toughness balance of plain low-carbon steel

STRUCTURE AND MECHANICAL PROPERTIES OF A SERIES OF STRUCTURAL STEEL AFTER HEAT TREATMENT WITH ENDURANCE IN THE INTERCRITICAL TEMPERATURE INTERVAL

Effects of Heat Treatment Process on Microstructure and Mechanical Properties for Extra-Thick High-Strength Steel Plate

Heat treatment in two phase region and its effect on microstructure and mechanical strength after welding of a low carbon steel

Effect of Different Heat Treatment Processes on Microstructures and Mechanical Properties of DP Steels

Atom-probe tomographic and dilatometric studies of phase-transformations after inter-critical annealing of a low-carbon dual-phase steel

Influence of Various Heat Treatment Cycles on the Phase Transformation and Microstructure Evolution of AISI 329 Super-Duplex Stainless Steel

Effect of Annealing Process on Microstructure, Texture, and Mechanical Properties of a Fe-Si-Cr-Mo-C Deep Drawing Dual-Phase Steel

Annealing Temperature-Dependent Microstructure, Mechanical, and Tribological Properties of Intercritically Heat-Treated Dual-Phase Steel

Effect of Heat Treatment on Mechanical Properties and Microstructure of Advanced High-Strength Steel

Strengthening of High-Alloy Steel through Innovative Heat Treatment Routes

Stability of retained austenite in high carbon steel – Effect of post-tempering heat treatment

Spheroidization heat treatment and intercritical annealing of low carbon steel

Impact of a Multi-step Heat Treatment on Different Manufacturing Routes of 18CrNiMo7-6 Steel

Analysis on continuous cooling transformation and microstructure control of 900 MPa grade high strength steel

Effect of Intercritical Temperature on the Microstructure and Mechanical Properties of a Ferritic–Martensitic Dual-Phase Low-Alloy Steel with Varying Nickel Content

Effect of holding time on the microstructure and mechanical properties of dual-phase steel during intercritical annealing

Influence of Intercritical Temperature on the Microstructure and Mechanical Properties of 6.5 Pct Ni Steel Processed by Ultra-fast Cooling, Intercritical Quenching and Tempering

Influence of Post-Weld Heat Treatment on Microstructural and Mechanical Properties of Dual-Phase Steel Gas Metal Arc-Welded Joints

Achieving High Plasticity and High Toughness of Low-Carbon Low-Alloy Steel through Intercritical Heat Treatment