Abstract:Plasma electrolytic oxidation (PEO) processing of EV 31 magnesium alloy has been carried out in fluoride containing electrolyte under bipolar pulse current regime. Unusual PEO cathodic micro-discharges have been observed and investigated. It is shown that the cathodic micro-discharges exhibit a collective intermittent behavior which is discussed in terms of charge accumulations at the layer/electrolyte and layer/metal interfaces. Optical emission spectroscopy is used to determine the electron density (typ. 10 15 cm-3) and the electron temperature (typ. 7500 K) while the role of F-anions on the appearance of cathodic micro-discharges is pointed out. Plasma Electrolytic Oxidation (PEO) is a promising plasma-assisted surface treatment of light metallic alloys (e.g. Al, Mg, Ti). Although the PEO process makes it possible to grow oxide coatings with interesting corrosion and wear resistant properties, the physical mechanisms of coating growth are not yet completely understood. Typically, the process consists in applying a high voltage difference between a metallic piece and a counter-electrode which are both immersed in an electrolyte bath. Compare to anodizing, the main differences concern the electrolyte composition and the current and voltage ranges which are at least one order of magnitude higher in PEO 1. These significant differences in current and voltage imply the dielectric breakdown and consequently the appearance of micro-discharges on the surface of the sample under processing. Those micro-discharges are recognized as being the main contributors to the formation of a dielectric porous crystalline oxide coating. 2 Nevertheless, the breakdown mechanism that governs the appearance of those micro-discharges is still under investigation. Hussein et al. 3 proposed a mechanism with three different plasma formation processes based on differences in plasma chemical composition. The results of Jovovi{\'c} et al. 4,5 concerning physical properties of the plasma seem to corroborate this mechanism, and also point out the importance of the substrate material in the plasma composition. 6 Compared with DC conducted PEO process, using a bipolar pulsed DC or AC current supply gives supplementary control latitude through the current waveform parameters. The effect of these parameter on the micro-discharges behavior has been investigated in several previous works. 2,3,7,8 One of the main results of these studies is the absence of micro-discharge during the cathodic current half-period. 9-11 Even if the cathodic half-period has an obvious effect on the efficiency of PEO as well as on the coating growth and composition, the micro-plasmas appear only in anodic half-period. Sah et al. 8 have observed the cathodic breakdown of an oxide layer but at very high current density (10 kA.dm-${}^2$), and after several steps of sample preparation. Several models of micro-discharges appearance in AC current have already been proposed. 1,2,8,12,13 Though cathodic micro-discharges have never been observed within usual process conditions, the present study aims at defining suitable conditions to promote cathodic micro-discharges and at studying the main characteristics of these micro-plasmas.

Growth behaviour of low-energy plasma electrolytic oxidation coatings on a magnesium alloy

Preparation and characterization of the low-energy plasma electrolysis oxide coatings on Mg Li alloy

Self-repairing Capability of Magnesium Alloy During the Plasma Electrolytic Oxidation Process

A Mechanism for the Growth of a Plasma Electrolytic Oxide Coating on Al

Research Progress on the Wear and Corrosion Resistant Plasma Electrolytic Oxidation Composite Coatings on Magnesium and Its Alloys

Enhanced corrosion resistance of magnesium alloy by plasma electrolytic oxidation plus hydrothermal treatment

Magnesium AZ63 Alloy Protective Coatings by Plasma Electrolytic Oxidation in Mixed Aqueous Electrolytes

Effect of cathode pulse square-wave on the microstructure and corrosion resistance of PEO coatings of AZ91D magnesium alloy prepared in the Na2C4H4O6–KF–Na2SiO3 system

The growth mechanism and corrosion resistance of laser-assisted plasma electrolytic oxidation (PEO) composite coating on AZ31B magnesium alloy

Microstructure and Corrosion Behavior of PEO-Coated AA7075 Under Pulsed Unipolar Potential Control Mode

Advances in amelioration of plasma electrolytic oxidation coatings on biodegradable magnesium and alloys

Effect of introduction of MXene on low energy plasma electrolytic oxidation

Degradation Rate Control Issues of PEO-Coated Wrought Mg0.5Zn0.2Ca Alloy

Plasma Electrolytic Oxidation of AZ91D Magnesium Alloy with Different Additives and Its Corrosion Behavior

Plasma Electrolytic Oxidation Treatment on Magnesium Rare Earth Alloy: Effect of Low Current Density

Influence of Plasma Electrolytic Oxidation on Fatigue Behaviour of ZK60A-T5 Magnesium Alloy

The Evidence of Cathodic Micro-discharges during Plasma Electrolytic Oxidation Process

Diagnostics of the Thickness of a Plasma Electrolytic Oxidation Coating on a Nanostructured Mg-Sr Alloy

Impact of voltage variation on topography, hydrophobicity, and corrosion behavior of the CeO2-TiO2 nanocomposite coating on AM60B Mg alloy prepared by plasma electrolyte oxidation

Growth mechanisms for initial stages of plasma electrolytic oxidation coating on Al

Environmental Friendly Plasma Electrolytic Oxidation of Am60 Magnesium Alloy and Its Corrosion Resistance