Abstract:Introduction: In the past three decades, additive manufacturing (AM), also known as 3D printing, has emerged as a promising technology, which allows the manufacture of complex parts by adding material layer upon layer. In comparison, with other metal-based AM technologies, gas metal arc welding-based additive manufacturing (GMAW-based AM) presents a high deposition rate and has the potential for producing medium and large metal components. To validate the technological performance of such a manufacturing process, the internal quality of manufactured parts needs to be analyzed, particularly in the cases of manufacturing the parts working in a critical load-bearing condition. Therefore, this paper aims at investigating the internal quality (i.e., and mechanical properties) of components manufactured by the GMAW-based AM technology. Method: A gas metal arc welding robot was used to build a thin-walled component made of mild steel on a low-carbon substrate according to the AM principle. Thereafter, the specimens for observing and mechanical properties were extracted from the built thin-walled component. The of the specimen were observed by an optical microscope; the hardness was measured by a digital tester, and the tensile tests were carried out on a tensile test machine. Results: The results show that the GMAW-based AM-built thin-walled components possess an adequate that varies from the top to the bottom of the built component: structures with primary dendrites in the upper zone; granular structure of with small regions of at grain boundaries in the middle zone, and grains of in the lower zone. The hardness (ranged between 164±3.46 HV to 192±3.81 HV), yield strength (YS offset of 0.2% ranged from 340±2 to 349.67±1.53 ), and ultimate tensile strength (UTS ranged from 429±1 to 477±2 ) of the GMAW-based AM-built components were comparable to those of wrought mild steel. Conclusions: The results obtained in this study demonstrate that the GMAW-based AM-built components possess adequate and good mechanical properties for real applications. This allows us to confirm the feasibility of using a conventional gas metal arc welding robot for additive manufacturing or repairing/re-manufacturing of metal components.

Fundamental Experiments of Pulsed GMA Additive Manufacturing

Impact of Process Parameters on Forming Quality and Deposition Efficiency of Unsupported Rods in Wire Arc Additive Manufacturing

Review of Wire Arc Additive Manufacturing for 3D Metal Printing

Wire Arc Additive Manufactured Radial Thin Wall: Fabrication Strategy, Macroscopic Defect Control, Microstructure, and Mechanical Properties

Wire Arc Additive Manufacturing: A Comprehensive Review and Research Directions

Analysis of Favorable Process Conditions for the Manufacturing of Thin-Wall Pieces of Mild Steel Obtained by Wire and Arc Additive Manufacturing (WAAM)

Effect of In-Process Active Cooling on Forming Quality and Efficiency of Tandem GMAW–based Additive Manufacturing

Development of a Low-Cost Wire Arc Additive Manufacturing System

Wire Arc Additive Manufacturing (WAAM) of Aluminum Alloy AlMg5Mn with Energy-Reduced Gas Metal Arc Welding (GMAW)

Development and Implementation of Wire Arc Additive Manufacturing (WAAM) Based on Pulse Spray GMAW for Aluminum Alloy (AlSi7Mg)

Wire arc metal additive manufacturing using pulsed arc plasma (PAP-WAAM) for effective heat management

Parameter Optimization of WAAM with Pulsed GMAW for Manufacturing Propeller-Shaped Blade

Process Optimization, Microstructure and Mechanical Properties of Wire Arc Additive Manufacturing of Aluminum Alloy by Using DP-GMAW Based on Response Surface Method

Wire arc additive manufacturing using high-strength steel tubular and solid wires

A review on wire arc additive manufacturing based on cold metal transfer

A preliminary study on gas metal arc welding-based additive manufacturing of metal parts

Assessing the pros and cons of wire-arc additive manufacturing for material production

Hybrid Additive and Subtractive Manufacturing Method Using Pulsed Arc Plasma

Experimental investigation on improving the deposition rate of gas metal arc-based additive manufacturing by auxiliary wire feeding method

Wire and arc additive manufacturing of metal components: a review of recent research developments

Selection of Parameters for Optimized WAAM Structures for Civil Engineering Applications