Abstract:Most design and analysis methods widely used for horizontal axis wind turbine performance prediction, such as the PROP code, are based on the traditional 2-D blade element/momentum theory (BEMT) methods, which are inadequate and underpredict the wind turbine rotor power output in the high-wind/peak-power condition, owing to effects of rotation on the wind turbine blade boundary layer. Although the deficiencies of the methods have been known for some time, this area has been neglected. The continued development of viable and well-established stall-regulated wind-turbine technology makes this research topic timely and particularly relevant to reducing the cost of wind energy. The main aim of the present paper is to describe and analyze the fundamental flow phenomena that characterize the boundary layer on rotating blades, and to develop a preliminary stall-delay model that modifies the 2-D airfoil data so as to simulate the 3-D stall-delay effects. The following steps were taken in the development of the model: 1) analysis of the 3-D integral boundarylayer equations for a reference system rotating with the blade, 2) description of the effects of rotor rotation on the separation point and its causes, and 3) determination of a simple correction formula to obtain rotating rotor lift coefficient Ci(a) and drag coefficient Cd(a) data from measured 2-D airfoil data. The preliminary 3-D stall-delay model consists of two key parameters (the ratio of local chord to local radius c/r the ratio of rotation speed to freestream velocity A) and three empirical correction factors Copyright © 1998 by the American Institute of Aeronautics and Astronautics, Inc. and the American Society of Mechanical Engineering. All rights reserved. ^Visiting Scholar. 'Assistant Professor, Senior Member AIAA. (a, b, d}. The stall-delay model is consistent with the blade element/momentum theory method and the Viterna/Tangler model, and the 3-D stall-delay model can be incorporated into the state of the art performance prediction codes, such as PROP. Through comparison with the field test data, the new model for 3-D stall-delay shows good agreement between predictions and experiments. The new model should be of great use in existing codes for horizontal axis wind turbine design and analysis.

Blockage corrections for wind tunnel tests conducted on a Darrieus wind turbine

Effect of Wind Tunnel Blockage on the Performance of a Horizontal Axis Wind Turbine with Different Blade Number

Experimental Study of Two-Stage Savonius Rotors with Different Gap Ratios and Phase Shift Angles

Numerical Investigation on the Flow and Power of Small-Sized Multi-Bladed Straight Darrieus Wind Turbine

Aerodynamic Performance Evaluation with a New Method for Darrieus Wind Turbine

NUMERICAL INVESTIGATION OF THE BLADE PROFILE EFFECT ON THE AERODYNAMIC PERFORMANCE OF A VERTICAL-AXIS WIND TURBINE DARRIEUS H-ROTOR

Wind tunnel and numerical study of a small vertical axis wind turbine

Performance analysis of an idealized Darrieus–Savonius combined vertical axis wind turbine

Numerical investigation on the spanwise chord distribution effects on the performance of an H-darrieus vertical axis wind turbines

Critical issues in the CFD simulation of Darrieus wind turbines

Aerodynamic characterization of a H-Darrieus wind turbine with a Drag-Disturbed Flow device installation

A 3-D Stall-Delay Model for Horizontal Axis Wind Turbine Performance Prediction

Computational Optimization of Adaptive Hybrid Darrieus Turbine: Part 1

Flow measurement in a wind tunnel with blockage screens

Numerical investigation of 3D unsteady flow around a rotor of vertical axis wind turbine darrieus type H

Numerical Investigation of Hybrid Savonius-Darrieus Vertical Axis Wind Turbine at Low Wind Speeds

Analysis of Blockage Correction Methods for High-Solidity Hydrokinetic Turbines: Experimental and Numerical Investigations

Numerical and Experimental Study on Performance Enhancement of Darrieus Vertical Axis Wind Turbine With Wingtip Devices

Effect of rotation curvature correction and inviscid spatial discretization scheme on the aerodynamics of vertical axis wind turbine

Experimental and Numerical Investigation of Tubercles and Winglets Horizontal Axis Wind Turbine Blade Design

Numerical Investigation on J‐Shaped Straight‐Bladed Darrieus Vertical Axis Wind Turbines Equipped with Gurney Flaps