Abstract:Objectives: This study characterized the feldspathic ceramic surfaces after various silanization protocols. Methods: Ceramic bars (2 mm × 4 mm × 10 mm) (N = 18) of feldpathic ceramic (VM7, VITA Zahnfabrik) were manufactured and finished. Before silane application, the specimens were ultrasonically cleaned in distilled water for 10 min. The ceramic specimens were randomly divided into nine groups (N = 2 per group) and were treated with different silane protocols. MPS silane (ESPE-Sil, 3M ESPE) was applied to all specimens and left to react at 20°C for 2 min (G20). After drying, the specimens were subjected to heat treatment in an oven at 38°C (G38), 79°C (G79) or 100°C (G100) for 1 min. Half of the specimens of each group were rinsed with water at 80°C for 15s (G20B, G38B, G79B, G100B). The control group (GC) received no silane. Attenuated total reflection infrared Fourier transform analysis (ATR FT-IR) was performed using a spectrometer. Thickness of silane layer was measured using a spectroscopic ellipsometer working in the λ = 632.8 nm (He-Ne laser) at 70° incidence angle. Surface roughness was evaluated using an optical profilometer. Specimens were further analyzed under the Scanning Electron Microscopy (SEM) to observe the topographic patterns. Results: ATR FT-IR analysis showed changes in Si-O peaks with enlarged bands around 940 cm(-1). Ellipsometry measurements showed that all post-heat treatment actions reduced the silane film thickness (30.8-33.5 nm) compared to G20 (40 nm). The groups submitted to rinsing in hot water (B groups) showed thinner silane films (9.8-14.4 nm) than those of their corresponding groups (without washing) (30.8-40 nm). Profilometer analysis showed that heat treatments (Ra ≈ 0.10-0.19 μm; Rq ≈ 0.15-0.26 μm) provided a smoother surface than the control group (Ra ≈ 0.48 μm; Rq ≈ 0.65 μm). Similar patterns were also observed in SEM images. Significance: Heat treatment after MPS silane application improved the silane layer network. Rinsing with boiling water eliminated the outmost unreacted regions of the silane yielding to thinner film thicknesses.

Characterization of Synthetic Amorphous Silica (SAS) Used in the Ceramics Industry

Production and characterization of silica materials from rice husk ash by different combustion processes

Study of the effect of the morphology of initial powders on the structural and dimensional characteristics of SiC-based porous ceramic materials

Comparison of the Properties of Calcium Silicates Derived from Different Raw Materials

New Insights Into Method Development and Characterization of Amorphous Silica From Wheat Straw

Determination of Total Silicon and SiO2 Particles Using an ICP-MS Based Analytical Platform for Toxicokinetic Studies of Synthetic Amorphous Silica

Effect of silica/alumina ratio and structure-directing agent on the physical and chemical properties of SAPO-34

Influence of ratio of silicon complex and coagulant on silicon dioxide physicochemical characteristics

SYNTHESIS AND CHARACTERIZATION OF SILICOALUMINOPHOSPHATE MOLECULAR SIEVES FROM METAKAOLIN

Effect of Temperature and Method of Synthesis on Morphology and Phase Transition of Amorphous and Crystalline Nano Silica Extracted from Mission Grass (Pennisetum Polystachion)

"Materials Studio" Simulation Study of the Adsorption and Polymerization Mechanism of Sodium Silicate on Active Silica Surface at Different Temperatures

SYNTHESIS AND CHARACTERIZATION OF PURE AMORPHOUS SILICON OXIDE FROM TREATED KAOLINITIC CLAY USING CHEMICAL EXTRACTION

Effects of Sample Preparation on Particle Size Distributions of Different Types of Silica in Suspensions

Synthesis of synthetic amorphous silica powder from palm oil mill fly ash extract by carbon dioxide impregnation

A Novel Method To Synthesize Amorphous Silica−Alumina Materials with Mesoporous Distribution without Using Templates and Pore-Regulating Agents

Influence of pre-treatment processes on the purity and characteristics of silica extracted from rice husk

Facile Extraction and Characterization of Silica Nanopowder from Marine National Park beach sand via Alkali Fusion Route

Surface characterization of feldspathic ceramic using ATR FT-IR and ellipsometry after various silanization protocols

Synthesis and characterisation of rice husk and palm fruit bunch silica: compositional, structural, and thermal analyses

Silica Functionalized Almond Gum Derivatives for Integrated Flocculation Cycles for Natural and Synthetic Water Systems

Industrial Wastes for Production of Thermally Stable and Corrosion Resistant alumino-silicate Refractory Ceramic Bodies