Abstract:Function, failure, and remodeling of the intervertebral disc are all related to the stress and strain fields in the tissue and may be calculated by finite element models with accurate material properties, realistic geometry, and appropriate boundary conditions. There is no comprehensive study in the literature investigating the shear material properties of the annulus fibrosus. This study obtained shear material properties of the annulus fibrosus and tested the hypothesis that these properties are affected by the amplitude and frequency of shearing, applied compressive stress, and degenerative state of the tissue. Cylindrical specimens with an axial orientation from seven nondegenerated and six degenerated discs were tested in torsional shear under dynamic and static conditions. Frequency sweep experiments over a physiological range of frequencies (0.1-100 rad/sec) at a shear strain amplitude of 0.05 rad were performed under three different axial compressive stresses (17.5, 25, and 35 kPa). At the largest compressive stress, shear strain sweep experiments (strain amplitude range: 0.005-0.15 rad at a frequency of 5 rad/sec) and transient stress-relaxation tests (shear strain range: 0.02-0.15 rad) were performed. The annulus fibrosus material was less stiff and more dissipative at larger shear strain amplitudes, stiffer at higher frequencies of oscillation, and stiffer and less dissipative at larger axial compressive stresses. The dynamic shear modulus, /G*/, had values ranging from 100 to 400 kPa, depending on the experimental condition and degenerative level. The shear behavior was also predominantly elastic, with values for the tangent of the phase angle (tandelta) ranging from 0.1 to 0.7. The annulus material also became stiffer and more dissipative with degenerative grade; however, this was not statistically significant. The results indicated that nonlinearities, compression/shear coupling, intrinsic viscoelasticity, and, to a lesser degree, degeneration all affect the shear material behavior of the annulus fibrosus, with important implications for load-carriage mechanisms in the intervertebral disc. These material complexities should be considered when choosing material constants for finite element models.

Impact of material properties of intervertebral disc on dynamic response of the human lumbar spine to vertical vibration: a finite element sensitivity study

The Effect of Disc Height and Degeneration on the Mechanical Behavior of Lumbar Spine:A Finite Element Analysis

Endplate Concavity Variation of Lumbar Motion Segments a Finite Element Analysis

[Analysis of Lumbar Disc Degeneration Using Three-Dimensional Nonlinear Finite Element Method].

Influence of the Morphology of Lumbar Motion Segment on Isthmic Stress and Facet Contact Force: A Finite Element Analysisangzh

Finite Element Model Analysis of Lumbar Biomechanical Characteristics after Nucleus Discectomy

Finite element analysis of the cervical spine: dynamic characteristics and material property sensitivity study

The impact of disc degeneration on the dynamic characteristics of the lumbar spine: a finite element analysis

The importance of intervertebral disc material model on the prediction of mechanical function of the cervical spine

Shear mechanical properties of human lumbar annulus fibrosus

The influence of bilateral pedicle screw fixation on vibration response of the disc degenerated human lumbar spine: A finite element stress analysis

The effect of structural changes on the low strain rate behaviour of the intervertebral disc

Regional variations of mechanical responses of IVD to 7 different motions: An in vivo study combined with FEA and DFIS

Mechanical analysis of the lumbar vertebrae in a three-dimensional finite element method model in which intradiscal pressure in the nucleus pulposus was used to establish the model

Impact of extracellular matrix and collagen network properties on the cervical intervertebral disc response to physiological loads: A parametric study

Biomechanical properties of lumbar endplates and their correlation with MRI findings of lumbar degeneration

Effect of asymptomatic intervertebral flexion patterns on lumbar disc pressure: A finite element analysis study

Validation and application of an intervertebral disc finite element model utilizing independently constructed tissue-level constitutive formulations that are nonlinear, anisotropic, and time-dependent

The effect of non-fusion dynamic stabilization on biomechanical responses of the implanted lumbar spine during whole-body vibration

Biomechanical Effect of Disc Height on the Components of the Lumbar Column at the Same Axial Load: A Finite-Element Study

Study on the Process of Intervertebral Disc Disease by the Theory of Continuum Damage Mechanics.