Abstract:Studying the mechanical properties of argillaceous rocks is of major interest in geoscience. For example, these rocks are important in engineering applications such as being suitable cap-rocks for the geological storage of carbon dioxide and potential host rocks for the storage of nuclear waste. Furthermore, argillaceous rocks are encountered in different natural settings such as accretionary wedges or fault zones. As a result of their sedimentary and diagenetic history clay rich rocks are often characterised by multiscale textural anisotropy and compositional heterogeneity resulting in anisotropic mechanical and hydraulic properties. Here, we studied the anisotropic deformation behaviour of Opalinus Clay, collected from the Mont Terri underground laboratory, which is the envisaged host rock formation for nuclear waste disposal in Switzerland. We used the sandy facies of Opalinus Clay, characterized by an irregular wavy lamination of quartz-rich and carbonate-cemented lenses with clay-rich interlayers. Unconsolidated-cylindrical samples cored at 0&#176;, 45&#176; and 90&#176; to the macroscopically visible bedding were deformed in undrained constant strain rate experiments using a Paterson-type deformation apparatus. For each orientation, tests were performed at dry conditions varying either confining pressure (in the range of 50 - 100 MPa), temperature (25 - 200 &#176;C) or strain rate (1*10-3 - 5*10-6 s-1) to study the influence of testing condition and sample orientation on the deformation behaviour. In addition, we deformed a set of back saturated samples at fixed conditions of 50 MPa, 100 &#176;C and 5*10-4 s-1 to investigate the effect of water content on the material strength. The results show semi-brittle deformation with low yield strength and strain weakening behaviour, in which strain is localized in sub-millimetre to millimetre-wide shear zones at all conditions. Increasing water content reduces, whereas increasing confining pressure increases the peak strength. Samples that were deformed parallel to bedding orientation exhibit the highest strength compared to samples with an orientation of 90&#176; and 45&#176; to bedding. Only for the latter orientations a weak correlation was found between temperature and failure behaviour. The variation of strain rate shows no clear influence for all orientations. Within this test series, there appears to be a potentially greater influence of the porosity on the peak strength for 45&#176; and 90&#176; oriented samples. Clay rich layers seem to have a strong influence on localization and formation of shear zones, in particular for samples oriented at 45&#176; and 90&#176; to bedding. This observation was confirmed by electron microscopy performed on broad ion beam polished surfaces of deformed sample material. Our experiments reveal that water content, sample orientation with respect to bedding and confining pressure are the most important factors influencing the peak strength of the sandy facies of Opalinus Clay, whereas compositional heterogeneity is responsible for the localization behaviour.

Mechanical Behavior of Claystone in Lateral Decompression Test and Thermal Effect

Investigating Temperature Effects on the Shear Behavior of Clays: Molecular Dynamics Simulations

Inducing Tensile Failure of Claystone Through Thermal Pressurization in a Novel Triaxial Device

Loading-unloading behavior of a clayey rock under thermo-hydro-mechanical conditions

Transversely Isotropic Poroelastic Behaviour of the Callovo-Oxfordian Claystone: A Set of Stress-Dependent Parameters

Thermo-poro-elastic behaviour of a transversely isotropic shale: Thermal expansion and pressurization

Experimental Deformation of Sandy Opalinus Clay at Elevated Temperature and Pressure Conditions

A laboratory investigation of thermally induced pore pressures in the Callovo-Oxfordian Claystone

Experimental and Numerical Investigation on the Tensile Fracture of Compacted Clay

Effects of Temperature and Thermal Cycles on the Elastic Shear Modulus of Saturated Clay

Analysis of Thermally-Induced Fracture of Callovo-Oxfordian Claystone: from Lab Tests to Field Scale

Elastic Stiffness Modelling of Opalinus Clay Based on Laboratory Measurements with Implications for In-situ Testing

Experimental Deformation of Opalinus Clay at Elevated Temperature and Pressure Conditions: Mechanical Properties and the Influence of Rock Fabric

Thermal Creep and Stress Relaxation of London Clay

Experimental Investigation of Thermo-Mechanical Behaviors of Deep-Sea Clay from the South China Sea

@Modelling of failure and fracture development of the Callovo-Oxfordian claystone during an in-situ heating experiment associated with geological disposal of high-level radioactive waste

Thermal Effect on the Compaction Behavior of Tight Shale by Uniaxial Strain Test

Deformation and Strength Characteristics of Structured Clay under Different Stress Paths

Effects of Clay Content on the Volumetric Behavior of Loess under Heating-Cooling Cycles

Analysis of compressibility and mechanical behavior of red clay considering structural strength

Effects of drying–wetting cycles on small-strain stiffness characteristics of fissured clay