Abstract:In this work, a combination of heat treatment (HT) and surface strengthening is explored to adjust the residual stress distribution in 316L stainless steel manufactured by laser powder bed fusion (L-PBF). Different HT in the range 750 °C–950 °C were applied to relieve the overall residual stress, followed by low-temperature gaseous carburization (LTGC) to introduce compressive residual stress in the surface region. The results indicate that the hierarchical microstructure in as built 316L gradually disappeared during HT, accompanied by the relaxation of thermal residual stresses, a reduction in hardness, yield strength and ultimate tensile strength and an improvement of the elongation. HT at 900 °C for 1 h is sufficient to completely relax residual stresses in the built. At elevated temperatures, low angle grain boundaries (LAGBs) vanish, leading to a rapid change in mechanical properties. Based on these findings, the impact of different microstructures in HT specimens on the application of LTGC was investigated. It reveals that all HT specimens exhibited the formation of a uniform, approx. 30 μm thick, case after LTGC. This case possesses high hardness (∼12 GPa) and a carbon content at the surface of ∼3 wt%. Although interdependencies occur between composition, residual stress and hardness profiles over the thickness of the expanded austenite zone, the differences in hardness and composition profiles for different conditions are minor, albeit measurable. In contrast, the residual stress profiles over the expanded austenite zone are notably affected by the initial residual stress present in the starting material and the yield stress associated with the cellular structure.

The Effect of Specimen Thickness on Low Temperature Gaseous Carburization of 316L Austenitic Stainless Steel

Mechanical properties and cracking behavior of low-temperature gaseous carburized austenitic stainless steel

Effects Of Low Temperature Supersaturation Gaseous Carburization On Mechanical Properties Of 316l Austenitic Stainless Steel

Stability of low-temperature-gaseous-carburization layer in AISI316L stainless steel at high temperature

Mechanical properties of low-temperature gaseous carburizated layer in 316L stainless steel based on nano-indentation and four-point bending tests

Influence of Plastic Pre-Strain on Low-Temperature Gas Carburization of 316L Austenitic Stainless Steel

Effect of surface nanocrystallization on low-temperature gas carburization for AISI 316L austenitic stainless steel

On the fatigue behavior of low-temperature gaseous carburized 316L austenitic stainless steel: Experimental analysis and predictive approach

The Effect of Surface Self-Nanocrystallization on Low-Temperature Gas Carburization for AISI 316L Steel

The low-cycle fatigue, deformation and final fracture behaviour of an austenitic stainless steel

Anisotropic response of additively manufactured 316 L stainless steel towards low-temperature gaseous carburization

Redistribution of carbon and residual stress in low-temperature gaseous carburized austenitic stainless steel during thermal and mechanical loading

Suppression of hydrogen absorption into 304L austenitic stainless steel by surface low temperature gas carburizing treatment

Residual stress relaxation in the carburized case of austenitic stainless steel under alternating loading

Exploration on the fatigue behavior of low-temperature carburized 316L austenitic stainless steel at elevated temperature

Effect of tensile stress on the formation of S-phase during low-temperature plasma carburizing of 316L foil

Effect of Gas Content and Treatment Temperature on the Characteristic of Surface Layers of Low Temperature Plasma Nitrided 316L Austenitic Stainless Steel

Microstructure and Mechanical Properties of Low Temperature Carburizing Layer on AISI 440C Martensitic Stainless Steel

Deformation Mechanisms of Selective Laser Melted 316l Austenitic Stainless Steel in High Temperature Low Cycle Fatigue

Effect of Surface Modification on the High Temperature Low Cycle Fatigue Performance of LPBF 316L Austenitic Steel

Response of laser power bed fusion manufactured austenitic stainless steel towards combined heat treatment and low-temperature thermochemical surface strengthening