Abstract:Drying is a very important unit operation in many industries such as food, pharmaceuticals, chemicals and ceramics. In most cases, wet materials are dried by forced convection using hot air flow. Heat and mass transfer processes during drying have been studied by both experimental and numerical simulation methods. For the purpose of studying the mechanism of heat and mass transfer and stress-strain distribution during the hot air drying of biological porous medium, two-way coupled thermo-hydro-mechanical mathematical model has been developed to simulate the hot air convective drying process of biological porous media on basis of Fickian diffusion theory, Fourier’s law of heat conduction and thermoelasticity mechanics. The following assumptions were made in order to find a solution to the hot air drying model: the biological porous medium was homogeneous and isotropic; the deformation during drying was elastic. The transient model, composed of a system of partial differential equations, was solved by finite difference methods. The computational procedure was programmed using C language. Some physical and mechanical properties of carrot changing with dry basis moisture content and temperature were considered. The numerical results were compared with available experimental data obtained during the drying of potatoes and carrots. The relative errors between numerical results and experimental data were both less than 5%, which showed the numerical results obtained using the mathematical model were in good agreement with the experimental data. Numerical simulations of the drying curve variations and the spatio-temporal distributions of moisture, temperature and drying stresses and strains of carrot were also evaluated. The temperature and moisture content showed a gradient inside carrot slice during drying. As the drying process proceeded, the temperature inside the carrot slice initially increased to reach the wet bulb temperature of the environment and eventually leveled off. The dry basis moisture content inside the carrot slice decreased, with the fastest decreased at the heat and mass transfer interface, eventually reached the equilibrium moisture content of the potato and leveling off. Both the moisture content gradient and the temperature gradient decreased gradually in the thickness direction. The normal stress was negative in all parts of the carrot slice, and the larger the closer to the evaporation interface. The shear stress was positive in all parts of the carrot slice, and the maximum shear stress occurred in the middle of the carrot slice. As in the case of the normal stress, the values of the normal strain were negative. The change trend of normal strain with time was consistent with that of moisture content. These results indicated that the observed physical deformations were caused by the dehydration of carrot slice during drying. The influence of drying conditions, such as air temperature, air velocity and the thickness of porous media on drying process was analyzed. Analysis showed that under certain drying conditions, the higher air temperature, the greater air velocity and the thinner slice thickness, the shorter drying time. This work should help in developing an understanding of the relationship between mass and heat transfer, shrinkage, stress, strains and physical degradation.

The kinetic model and temperature effect of Caulerpa Lentillifera drying process

Kinetic study and modelling of drying of Chlorella vulgaris

A fully coupled multiphase model for infrared-convective drying of sweet potato

Semi-Empirical Mathematical Modeling, Energy and Exergy Analysis, and Textural Characteristics of Convectively Dried Plantain Banana Slices

Effect of air velocity, temperature, and relative humidity on drying kinetics of rubberwood

Mathematical Modeling of Drying Kinetics and Technological and Chemical Properties of Pereskia sp. Leaf Powders

Mathematical Model and Numerical Simulation of Biological Porous Medium During Hot Air Drying

Nutritional value, bioactive composition, physico-chemical and sensory properties of Ulva sp. and Fucus vesiculosus depending on post-harvest processing: a drying comparison study

Effect of drying kinetics model on energy efficiency of drying systems

Kinetic Model of Moisture Loss and Polyphenol Degradation during Heat Pump Drying of Soursop Fruit (Annona muricata L.)

Heat Pump Drying of Kelp (Laminaria japonica): Drying Kinetics and Thermodynamic Properties

Integrated drying model of lychee as a function of temperature and relative humidity

Hot air and microwave drying kinetics of white cabbage (Brassica oleracae L. var capitata L.): Modelling, thermodynamic properties, energy consumption and reconstitution kinetics

Mathematical modeling of thin layer drying of carrot slices by forced convection

Hot-air drying characteristics of typical cork and the drying model

Equilibrium Moisture Content Modeling and Study of Circulating-Bed Drying Kinetics of Non-Fragrant and Fragrant Paddy Varieties

Effect of Hot Air Drying Temperature on Drying Kinetics, Physico-Chemical Properties, and Energy Consumption of Culture Asparagus (Asparagus officinalis L.)

Drying Kinetic Analysis of Municipal Solid Waste Using Modified Page Model and Pattern Search Method

Evaluating Kinetics of Convection Drying and Microstructure Characteristics of Asian Seabass Fish Skin without and with Ultrasound Pretreatment

Effect of ANN and semi-empirical models on dried Annona muricata leaves

Kinetic Modeling of Convective and Microwave Drying of Potato Peels and Their Effects on Antioxidant Content and Capacity