Abstract:Hydrodynamic model tests and numerical simulations may be combined in a complementary manner during the design and qualification of new offshore structures. In the EU H2020 project LIFES50+ (lifes50plus.eu), a model test campaign of floating offshore wind turbines using Real-Time Hybrid Model (ReaTHM) testing techniques was carried out at SINTEF Ocean in fall 2017. The present paper focuses on the process of calibrating a numerical model to the experimental results. The concepts tested in the experimental campaign was a 1:36 scale model of the public version of the 10MW OO-Star Wind Floater semi-submersible offshore wind turbine. A time-domain numerical model was developed based on the as-built scale model. The hull was considered as rigid, while bar elements were used to model the mooring system and tower in a coupled finite element approach. First-order frequency-dependent added mass, potential damping, and excitation forces/moments were evaluated across a range of frequencies using a panel method. Distributed viscous forces on the hull and mooring lines were added to the numerical model according to Morison’s equation. Potential difference-frequency excitation forces were also included by applying Newman’s approximation. The quasi static properties of the mooring system were assessed by comparing the restoring force and maximum line tension with the pull-out test. Drag coefficients for the line segments were estimated by imposing the measured fairlead motion from model tests as forced displacement and comparing the calculated and measured dynamic line tension. The linear and viscous damping coefficients were first estimated based on the decay tests, and the tuned damping coefficients were compared to initial guesses based on the Reynolds and Keulegan-Carpenter number at model scale. The results were then applied in the numerical model, and simulations in extreme irregular waves were compared to the experiments. It was found that second order drift forces proved to be significant, particularly for the severe irregular seastate. These could not be modelled correctly applying the potential drift forces together with quadratic damping matrix tuned to the free decay test. And the model with viscous drag coefficients tuned to decay tests also underestimated the slow drift motions. Thus, new viscous drag coefficients were determined to match the low frequency platform response. To inverstigate the performance of the tuned model, comparisons were made for a moderate seastate and for a simulation with both waves and wind on an operating turbine. In the end, possible further improvements to the modelling were suggested.

Real-Time Hybrid Model Testing of a Semi-Submersible 10MW Floating Wind Turbine and Advances in the Test Method

Real-time hybrid model tests of floating offshore wind turbines: Status, challenges, and future trends

Calibration of Hydrodynamic Coefficients for a Semi-Submersible 10 MW Wind Turbine

Experimental Investigation of the Coupling Between Aero- and Hydrodynamical Loads On A 12 MW Semi-Submersible Floating Wind Turbine

Multiple-degree-of-freedom actuation of rotor loads in model testing of floating wind turbines using cable-driven parallel robots

Model tests of a 10 MW semi-submersible floating wind turbine under waves and wind using hybrid method to integrate the rotor thrust and moments

Real-Time Hybrid Test Method for Floating Wind Turbines: Focusing on the Aerodynamic Load Identification

A Novel Real-Time Hybrid Testing Method for Twin-Rotor Floating Wind Turbines with Single-Point Mooring Systems

Model Test of a Semi-Submersible Floating Wind Turbine: Hydrodynamic Motions and Internal Loads

Integrated Numerical Investigation of a 15 MW Semi-Submersible Wind Turbine at Moderate Water Depth

Validation of a 750 kW semi-submersible floating offshore wind turbine numerical model with model test data, part II: Model-II

Model Tests on the Long-Term Dynamic Performance of Offshore Wind Turbines Founded on Monopiles in Sand

OC6 Phase I: Investigating the Underprediction of Low-Frequency Hydrodynamic Loads and Responses of a Floating Wind Turbine

Coupled aero-hydro-geotech real-time hybrid simulation of offshore wind turbine monopile structures

Wind/Wave Testing of A 1:70-Scale Performance-Matched Model of the IEA Wind 15 MW Reference Wind Turbine with Real-Time ROSCO Control and Floating Feedback

Development and performance study of a multi-degree-of-freedom loading device for real-time hybrid model testing of floating offshore wind turbines

Scaled Model Test Study of the Dynamic Behavior of an Offshore Wind Turbine Support Structure

Validation of a FAST semi-submersible floating wind turbine numerical model with DeepCwind test data

Experimental Comparison of Three Floating Wind Turbine Concepts

A large-scale wind turbine model installed on a floating structure: experimental validation of the numerical design

Validation of a Novel Floating Wind Turbine Simulation Tool via Benchmarking: Case Study of a Semi-Submersible Platform