Abstract:Many pieces of fine art are made of wood that has been treated with coatings. Since wood is a very hygroscopic material, the moisture content strongly influences the deformation of wooden parts. Coatings often act as moisture barriers. Therefore, the moisture permeability of coatings must be considered for the evaluation of the structural behaviour. The mechanical properties are also relevant to evaluate the deformation of thin artwork like panel paintings as well as the damage of paintings and varnishes. Therefore, the mechanical properties and the permeability of selected coatings used for cultural wooden artwork are investigated and presented in the article at hand. In this study, coatings of three artworks are investigated: a Lusatian cupboard from the eighteenth century, an altarpiece by L. Cranach the Elder and a Russian icon from 1912. The coatings considered are white ground, colours, varnishes, glue and textile reinforced sizing. Mechanical tests are conducted to evaluate the stiffness and tensile strength of the Russian icon's coating. Cup tests are made to identify the moisture permeability of the coatings. This test was conducted for single coatings as well as for coating systems consisting of different coatings to investigate both the moisture barrier of single coatings and the interaction of coatings. Exponential functions for the relative humidity-dependent permeability are fitted based on the experimental data. The results allow the quantification of permeability for all investigated coatings—from white ground with a high permeability to beeswax with a low permeability—and the magnitude of moisture dependency of the coating's permeability. Furthermore, it is shown that the simple addition of the water vapour resistance of single coatings underrates the resistance of a total coating system. By the mechanical tests, the strength, ultimate strain and Young's modulus are obtained. The permeability and the mechanical parameters are required as input for numerical simulations of the structural behaviour of coated wooden artwork. These results are a good step forward to assess the risk of damage of coated wooden artwork.

Effect of Ethylene Oxide Sterilization and Accelerated Ageing on the Physical and Mechanical Properties of Beech, Oak, and Elm Wood: Part 1

Effect of Ethylene Oxide Sterilization and Accelerated Ageing on the Physical and Mechanical Properties of Beech, Oak, and Elm Wood: Part 2

Mechanical Properties of Aged Glue Laminated Bamboo for Structural Members

Determination of changes in the mechanical and color properties of some wood species treated with shellac

Chemical changes in thermally modified, acetylated and melamine formaldehyde resin impregnated beech wood

Hygro-mechanical short-term behaviour of selected coatings: experiments and material modelling on vapour permeability and mechanical properties

Influence of Traditional Wood Surface Modification Methods on Changes in Aesthetic and Resistance Properties

Mechanical properties of beech wood treated with malic acid-based polyester

Effect of Thermal Treatment on the Chemical, Physical, and Mechanical Properties of Pedunculate Oak (Quercus robur L.) Wood

Wood Surface Finishing with Transparent Lacquers Intended for Indoor Use, and the Colour Resistance of These Surfaces during Accelerated Aging

Wood modification with N-methylol and N-methyl compounds: a case study on how non-fixated chemicals in modified wood may affect the classification of their durability

Comparative studies on the durability and moisture performance of wood modified with cyclic N-methylol and N-methyl compounds

Characterisation of thermally treated beech and birch by means of quasi-static tests and ultrasonic waves

Effects of thermal treatment on the mechanical properties of larch (Larix gmelinii) and red oak (Quercus rubra) wood cell walls via nanoindentation

Investigation of Roughness and Adhesion Strength Properties of Pine and Poplar Wood Heat Treated in Air and under Vacuum after Artificial Aging

Effects of different heat treatment media on odorous constituents, chemical decomposition and mechanical properties of two hardwoods

Degradation of Chemical Components of Thermally Modified Robinia pseudoacacia L. Wood and Its Effect on the Change in Mechanical Properties

The Effect of Steaming Beech, Birch and Maple Woods on Qualitative Indicators of the Surface

Impact of thermal modification on color and chemical changes of spruce and oak wood

Understanding changes in holocellulose and lignin compounds in wooden structure of veneers: Molecular insights post hydrothermal treatment and aging

Influence of polyethylene glycol and various carboxylic acids on the physical and mechanical properties of beech wood (Fagus sylvatica) and Scots pine wood (Pinus sylvestris)