Abstract:The anisotropy in creep aging behavior and microstructural evolution of AA2195-T34 A l–Li alloy plates under different stress levels at 180 °C were systematically investigated by constant-stress creep aging, mechanical property testing and microstructure characterization. The results indicated that the creep strain initially increases and then decreases with the angle relative to the rolling direction by cause of the divergences in the dislocation density and the number of movable sliding systems. The creep strain in 45° direction is 1.15 times and 1.41 times larger than that in 0° and 90° directions at a stress of 160 MPa, respectively. The creep strain in-plane anisotropy (IPA) value first increases rapidly, followed by a slight decrease with time, and declines with stress at the primary creep stage. The strength first increases and then tends to fluctuate around a constant value with the aging time because of the evolution of T 1 precipitates. As shown by the gradual reduction in the difference among the volume fractions of the brass texture of the alloy in the three directions, the strength IPA rapidly declined at the primary creep stage. The IPA values of the yield strength during the steady creep stage are 4.8%, at a stress of 160 MPa. Since the Schmidt factor of the material in the 45° direction is the largest, the yield strength in this direction is the lowest. A constitutive model considering the anisotropy of creep deformation and aging strengthening was established, of which the predicted results showed excellent consistency with the experimental values. The relative errors between the predicted and experimental values of the yield strength/steady creep strain in different directions do not exceed 1.7% and 4.3%, respectively.

Effects of Pre-Stretching on Creep Behavior, Mechanical Property and Microstructure in Creep Aging of Al-Cu-Li Alloy

The Effect of Al on Microstructure and Properties of Cu-15Ni-8Sn During the Aging

Achieving high strength and ductility of Al-Cu-Li alloy via creep aging treatment with different pre-strain levels

An Investigation of Compressive Creep Aging Behavior of Al-Cu-Li Alloy Pre-Treated by Compressive Plastic Deformation and Artificial Aging

Influence of pre-stretching at ambient and cryogenic temperatures on dislocation configuration, precipitation behaviour, and mechanical properties of 2195 Al-Cu-Li alloy

Study of pre-strain before artificial aging on mechanical property and stress corrosion behavior of 2297 Al–Cu–Li alloy

Effect of Process Parameters on Fatigue and Fracture Behavior of Al-Cu-Mg Alloy after Creep Aging

Influence of temperature on creep behavior, mechanical properties and microstructural evolution of an Al-Cu-Li alloy during creep age forming

Effect of Pre-Stretch on the Precipitation Behavior and the Mechanical Properties of 2219 Al Alloy

Effect of applied stress level on anisotropy in creep-aging behavior of Al–Cu–Li alloy

Creep behavior and mechanical properties of Al-Li-S4 alloy at different aging temperatures

Creep aging behavior of Al-Cu-Mg-Si alloy with elastic and plastic loads

Study on Multi-Step Creep Aging Behavior of Al-Li-S4 Alloy

Effects of Aging Temperature on the Mechanical Properties and Precipitation Behavior of a Pre-strained Al–Cu–Mg–Ag Alloy

Effects of pre-deformation on microstructure, mechanical properties and corrosion performance of an Al-Cu-Mg-Ag alloys

Effect of creep aging parameters on creep resistance behavior of Al–Cu–Mg alloy

Enhancing Stress Corrosion Cracking Resistance of Low Cu-Containing Al-Zn-Mg-Cu Alloys by Aging Treatment Control

Investigation of anisotropic creep-ageing behaviour of Al-Cu-Li alloy AA2050

Experimental and Simulation Study for the Influence of Thermal Pre-Deformation on Subsequent Aging Precipitation Kinetics of Al-Zn-Mg-Cu Alloy

Effect of stress level on anisotropy in creep ageing behaviour of 2195-T84 Al Li alloy

Anisotropy in creep-aging behavior of Al–Li alloy under different stress levels: experimental and constitutive modeling