Abstract:Reactivity controlled compression ignition (RCCI) combustion is a advanced low temperature combustion concept to reduce CO 2 and brake the trade-off between NOx and PM emissions for next generation compression ignition (CI) engines. However, it leads to the more complex multi-stage heat release in diesel/natural gas (NG) dual fuel engines and is criticized for extra-high methane and carbon monoxide emissions. Using the existing methods, it is difficult to effectively quantify the contribution of the accumulated heat release (AHR) at each stage to the whole combustion process and to create their relevance to the performance and emissions in the RCCI engines. In this paper, experiments were conducted on a ship diesel/NG dual-fuel engine at a load of 25 %. A new identification and quantitative analysis method of multi-stage heat release is proposed, and the coupling effects of the diesel split injection parameters on the multi-stage heat release and performance in the RCCI engine were revealed. The results show that the new method is not only available for analyzing the combustion of traditional CI engines but also is more effective for identifying the multi-stage combustion in RCCI engines. For the increased pre-injection ratio (PR), as the start of first injection (SOI-I) and the start of second injection (SOI-II) advance, the AHR in Stage-I (Q-Stage-I) decreases, and the increased Q-Stage-III lead to the improved indicated thermal efficiency (ITE > 49 %). Meanwhile, methane (CH 4 ), non-methane hydrocarbon (NMHC) and carbon monoxide (CO) emissions can be reduced by more than 50 %, while nitrogen oxides (NOx) emissions increase. The impact significance of SOI-II on Q-Stage-I and Q-Stage-III is higher, their values are + 65.88 % and −51.04 %, respectively, and the Q-Stage-II is mainly controlled by SOI-I. The impact significance of Q-Stage-III on ITE is the highest about + 69.43 %. Q-Stage-I shows a higher positive correlation with CH 4 , NMHC and CO emissions although the proportion of Q-Stage-I is far smaller than that of Q-Stage-II and Q-Stage-III. Therefore, the simultaneous reduction of incomplete combustion products and NOx emission can be achieved by reasonably adjusting split injection parameters.

Effects of piston geometry and injection strategy on the capacity improvement of waste heat recovery from RCCI engines utilizing DOE method

Numerical Simulation Of Re-Entrant Bowl Effects On Natural-Gas Spark-Ignition Operation

Thermodynamic and statistical analysis on the effect of exhaust gas recirculation on waste heat recovery from homogeneous charge compression ignition engines

Parametric study for small scale engine coolant and exhaust heat recovery system using different Organic Rankine cycle layouts

Experimental Investigations on Dynamic Performance of Organic Rankine Cycle Integrated with Latent Thermal Energy Storage under Transient Engine Conditions

Statistical analysis on the effect of premixed ratio, EGR, and diesel fuel injection parameters on the performance and emissions of a NG/Diesel RCCI engine using a DOE method

An Efficient Data-Driven Approach for Modeling and Optimization of Reactivity-Controlled Compression Ignition Engine Fueled with Polyoxymethylene Dimethyl Ethers and Hydrogen

Investigations on reactivity controlled compression ignition combustion with different injection strategies using alternative fuels produced from waste resources

Effects of piston bowl geometry on Reactivity Controlled Compression Ignition heat transfer and combustion losses at different engine loads

Combined effects of nozzle hole variation and piston bowl geometry modification on performance characteristics of a diesel engine with energy and exergy approach

Comparative analysis of inlet and outlet cavity designs on the thermal-hydraulic performance of compact heat exchangers for combustion engine exhaust heat recovery

Effect of Compression Ratio and Piston Geometry on RCCI Load Limits and Efficiency

Effect of piston bowl geometry and spray angle on engine performance and emissions in HCCI engine using multi‐stage injection strategy

Numerical Study on Double Injection Techniques in a Gasoline and Biodiesel Fueled RCCI (reactivity Controlled Compression Ignition) Engine

Combustion and Emission Enhancement of a Spark Ignition Two-Stroke Cycle Engine Utilizing Internal and External Exhaust Gas Recirculation Approach at Low-Load Operation

Enhancing reactivity-controlled compression ignition engine performance: A response surface methodology approach with ammonium hydroxide-waste cooking oil biodiesel optimization

Investigation of piston bowl geometry, injection timing, and EGR mass fraction to improve the performance of ISM 370 diesel engine

Effect of split injection strategy of diesel fuel on multi-stage heat release and performance of a RCCI engine fueled with diesel and natural gas

An experimental investigation on the influence of piston bowl geometry on RCCI performance and emissions in a heavy-duty engine

Predicting the effects of direct-injected fuels co-powered by high-CO2 biogas on RCCI engine emissions using kinetic mechanisms and multi-objective optimization

Experimental study on the effect of piston bowl geometry on the combustion performance and pollutant emissions of methane-diesel common rail dual-fuel engine