Abstract:The Haber–Bosch (HB) process is the primary chemical synthesis technique for industrial production of ammonia (NH3) for manufacturing nitrate-based fertilizer and as a potential hydrogen carrier. The HB process alone is responsible for over 2% of all global energy usage to produce more than 160 million tons of NH3 annually. Iron catalysts are utilized to accelerate the reaction, but high temperatures and pressures of atmospheric nitrogen gas (N2) and hydrogen gas (H2) are required. A great deal of research has aimed at increased performance over the last century, but the rate of progress has been slow. This Account focuses on determining the atomic-level reaction mechanism for HB synthesis of NH3 on the Fe catalysts used in industry and how to use this knowledge to suggest greatly improved catalysts via a novel paradigm of catalyst rational design.We determined the full reaction mechanism on the two most active surfaces for the HB process, Fe(111) and Fe(211)R. We used density functional theory (DFT) to predict the free-energy barriers for all 12 important reactions and the 34 most important 2 × 2 surface configurations. Then we incorporated the mechanism into kinetic Monte Carlo (kMC) simulations run for several hours of real time to predict turnover frequencies (TOFs). The predicted TOFs are within experimental error, indicating that the predicted barriers are within 0.04 eV of experiment.With this level of accuracy, we are poised to use DFT to improve the catalyst. Rather than forming bulk alloys with uniform concentration, we aimed at finding additives that strongly prefer near-surface sites so that minor amounts of the additive might lead to dramatic improvements. However, even for a single additive, the combinations of surface species and reactions multiplies significantly, with ∼48 reaction steps to examine and nearly 100 surface configurations per 2 × 2 site. To make it practical to examine tens of dopant candidates, we developed the hierarchical high-throughput catalysis screening (HHTCS) approach, which we applied to both the Fe(111) and Fe(211) surfaces. For HHTCS, we identified the most important 4 reaction steps out of 12 for the two surfaces to examine >50 dopant cases, where we required performance at each step no worse than for pure Fe. With HHTCS, the computational cost is about 1% of that for doing the full reaction mechanism, allowing us to do ≈50 cases in about 1/2 the time it took to do pure Fe(111). The new leads identified with HHTCS are then validated with full mechanistic studies.For Fe(111), we predict three high-performance dopants that strongly prefer the second layer: Co with a rate 8 times higher, Ni with a rate 16 times higher, and Si with a rate 43 times higher, at 400 °C and 20 atm. We also found four dopants that strongly prefer the top layer and improve performance: Pt or Rh 3 times faster and Pd or Cu 2 times faster. For Fe(211), the best dopant was found to be second-layer Co with a rate 3 times faster than that for the undoped surface.The DFT/kMC data were used to predict reshaping of the catalyst particles under reaction conditions and how to tune dopant content so as to maximize catalytic area and thus activity. Finally, we show how to validate our mechanistic modeling via a comparison between theoretical and experimental operando spectroscopic signatures.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.accounts.1c00789.Schematic depiction of the bcc surface structures here investigated also showing 4-fold binding sites (PDF)This article has not yet been cited by other publications.

Interplay Between Site Activity and Density of BCC Iron for Ammonia Synthesis Based on First‐Principles Theory

Regulating Intermediate Adsorption and H2O Dissociation on a Diatomic Catalyst to Promote Electrocatalytic Nitrate Reduction to Ammonia

Correlation Between the Structural Features and Intrinsic Activity Trend of Fe Surfaces for Ammonia Synthesis

Reaction Mechanisms, Kinetics, and Improved Catalysts for Ammonia Synthesis from Hierarchical High Throughput Catalyst Design

Robust Active Site Design of Single Atom Catalysts for Electrochemical Ammonia Synthesis

Impact of Active Site Density on Oxygen Reduction Reactions Using Monodispersed Fe-N-C Single-Atom Catalysts

Discovery of Dramatically Improved Ammonia Synthesis Catalysts through Hierarchical High-Throughput Catalyst Screening of the Fe(211) Surface

Understanding and Modifying the Scaling Relations for Ammonia Synthesis on Dilute Metal Alloys: From Single-Atom Alloys to Dimer Alloys

Analyzing the Active Site and Predicting the Overall Activity of Alloy Catalysts

Controlling the Shapes of Nanoparticles by Dopant-Induced Enhancement of Chemisorption and Catalytic Activity: Application to Fe-Based Ammonia Synthesis

Correlating C═C, C═O, and C═N Hydrogenation Activity with Hydrogen Binding Energies on Ni–Fe Bimetallic Catalysts

Unraveling the Enhanced N 2 Activity on CuNi Alloy Catalysts for Ammonia Production: Experiments, DFT, and Statistical Analysis

The synthesis mechanism of nitrogen to ammonia on the Fe, Co, Ni-doped Cu(1 0 0) Surface: A DFT study

Tackling the Activity Trend of Metal‐Loaded Metal Nitride Catalysts for NH3 Synthesis by a First‐Principles Microkinetic Study

On Scaling Relations of Single Atom Catalysts for Electrochemical Ammonia Synthesis

Heterogeneous Fe 3 single-cluster catalyst for ammonia synthesis via an associative mechanism

Iron-Single Sites Confined by Graphene Lattice for Ammonia Synthesis under Mild Conditions

Promotional Effect of Carbon on Fe Catalysts for Ammonia Decomposition: A Density Functional Theory Study

Flexible Iron Clusters Promoting Ammonia Synthesis: A Density Functional Theory Prediction

Design of Cu-based bimetals for ammonia catalytic combustion via DFT-based microkinetic modeling

Mechanistic Insight into Size-Dependent Activity and Durability in Pt/CNT Catalyzed Hydrolytic Dehydrogenation of Ammonia Borane