Abstract:Modern production machinery is equipped with multifunctional automated process control systems (APCS) based on software and hardware complexes (SHC) of a network hierarchical structure. The experience of designing and operating multifunctional process control systems proves that the efficiency of the systems being developed significantly depends on the array of problems at different stages of the technology design and system modernization. It is to be developed, both at the fundamental level of local automatic control systems and at a higher level of hierarchical system structure. At the same time, special attention is paid to the software failure, which is fixed, as a rule, by periodically updating all the content. For process control systems, such an approach under the operation conditions of power equipment is unacceptable. In this regard, the effectivity problems of complex systems are to be classified in terms of technological process factors, the theory of automatic control and instrumental factors associated with the proper software implementation. As a theoretical basis to solve the problem of information sufficiency and synthesis of structurally stable systems, the methods of potentials and coordinates of the thermodynamics of irreversible processes are used. The testing method is applied as a tool to analyze and diagnose software and hardware tools. The authors have defined three groups of factors: system, controller and local. The task to analyze the conformity of information and algorithmic support means to expert and verify the absence of defects in the software of a multifunctional system and the fulfillment of the declared requirements. The automated testing system is a unified environment to analyze the execution of test scenarios. It provides continuous validation and verification of the information and algorithmic support of the SHC. In particular, a methodology has been developed to carry out resource tests of the software and hardware complex and checking the operation of the mechanisms for backing up, synchronizing, and replacing its components by simulating failures in the processor modules, hardware and software components. A set of methodological factors has been defined to develop advanced software and hardware systems for process control systems. It significantly affects the adequacy of the information and algorithmic support of a complex system. A technology of automated testing of software and hardware tools of the SHC has been developed. Methods to solve interdisciplinary problems are generalized. The authors recommend solving the problems at the earlier stages of a complex system design. The proposed technology to develop and diagnose automatically software and hardware of the SHC by implementing a single environment to study, compare and detect the defects of the SHC software throughout the entire life cycle of the process control system allows you to identify and eliminate the mutual negative influence of the SHC components both at the development stage and at the stage of the subsequent system organization, including solving the problem of information security at the stage of system installation and operation. The developed approach to solve complex interdisciplinary problems that require solution at the early stages of designing complex systems makes it possible to avoid fundamentally erroneous decisions and increase the competitiveness of the SHC as a systemically important APCS complex at the time of installation.

PRINCIPLES OF APPROACH TO DETERMINATION OF TECHNOLOGICAL ELEMENT BASE FOR AUTOMATION OF MACHINING PRODUCTION PREPARATION THROUGHOUT CYCLE. Continuation

PRINCIPLES OF APPROACH TO DETERMINATION OF TECHNOLOGICAL ELEMENT BASE FOR AUTOMATION OF MACHINING PRODUCTION PREPARATION THROUGHOUT CYCLE

Composition of elements of integration of the technological element base in the structure of working machines for cutting processing

Output parameters at development and production stage of a product in its life cycle

Information and algorithmic support of streamlined control systems

Automated system of operational registration of technical changes of an enterprise of radio-electronic industry

Engineering process aspects of digitalization of machine-building production

ALGORITHM AUTOMATION METHODS FOR WORKING WITH NETWORK EQUIPMENT

Automation and digitalization of ultrasonic technological processes

Automation of technological processes in mechanical engineering

Automation design systems for mechanical engineering and device node design

Computer modeling and software research of car and engine parts

Dependence of Technological Line Automation on the Artificial Intelligence Coefficient of Modular Equipment

Application of intelligent engineering in the planning of cyber-physical production systems

STRUCTURE KNOWLEDGE BASED MECHANICAL PRODUCTS DESIGN TECHNOLOGY

Application of high-level methods of compromise optimization for control of autonomous robotized open pit mining

Automation of preproduction processes for high-precision small-sized parts on CNC machines

Innovative Ways to Ensure the Interoperability of a Complete Group of Processes in the Lifecycle of an Integrated Management System Based on their Synchronization

Supporting management and maintenance of manufacturing knowledge in design automation systems

OPTIMIZATION OF CUTTING MODES ON MACHINES OF FLEXIBLE MANUFACTURING SYSTEMS

The concept of intelligent control system of small-scale production