Abstract:Introduction: Tasks performed at or above head height in industrial workplaces pose a significant challenge due to their association with musculoskeletal disorders. Upper-body exoskeletons have been identified as a potential solution for mitigating musculoskeletal loads and fighting against excessive muscular fatigue. However, the influence of such support on fine motor control, as well as on cognitive-motor interference, has received limited attention thus far. Therefore, this crossover randomized study aimed to investigate the impact of the use of a passive upper-body exoskeleton in the presence of muscular fatigue or not. Additionally, focusing on differences between single (ST) and dual (DT) industrial tasks consisting of overhead speed and accuracy exercises. Methods: In both scenarios, N = 10 participants (5 male/5 female) engaged in an overhead precision task using a nail gun to precisely target specific areas on three differently sized regions, based on Fitts' law paradigm (speed-accuracy trade-off task). This was done with and without the passive upper-body exoskeleton, before and immediately after a fatiguing exercise of shoulder and leg muscles. In addition, a second task (dual-task, DT) was carried out in which the occurrence of an auditory signal had to be counted. The main outcomes were muscular activation of the shoulder girdle as well as the time to perform speed-accuracy tasks of different difficulty indexes (calculated by means of Fitts' law). Results and discussion: In the absence of fatigue, the exoskeleton did not affect the speed-accuracy trade-off management of participants in the single task, but it did in the dual-task conditions. However, after muscle fatigue, the speed-accuracy trade-off was differently affected when comparing its execution with or without the exoskeleton. In general, the dual task resulted in longer times to perform the different tasks, whether it was with or without the exoskeleton. Furthermore, the use of the exoskeleton decreased muscle activity, which is associated with less physical effort, but only significantly for the M. deltoideus and M. trapezius when compared by tasks. Overall, these study findings highlight the potential supportive effects of using an upper-body exoskeleton for industrial overhead tasks.

Biomechanical analysis of the upper body during overhead industrial tasks using electromyography and motion capture integrated with digital human models

Human Reliability Modeling in Occupational Environments Toward a Safe and Productive Operator 4.0

Leveraging Digital Perceptual Technologies for Remote Perception and Analysis of Human Biomechanical Processes: A Contactless Approach for Workload and Joint Force Assessment

Study on Static Biomechanical Model of Whole Body Based on Virtual Human

Inertial Motion Capture-Driven Digital Human for Ergonomic Validation: A Case Study of Core Drilling

Closed-Chain Inverse Dynamics for the Biomechanical Analysis of Manual Material Handling Tasks through a Deep Learning Assisted Wearable Sensor Network

ApOL-Application Oriented Workload Model for Digital Human Models for the Development of Human-Machine Systems

Impact of a passive upper-body exoskeleton on muscular activity and precision in overhead single and dual tasks: an explorative randomized crossover study

Digital ergonomic assessment to enhance the physical resilience of human-centric manufacturing systems in Industry 5.0

An Experimental Evaluation of the Proto-MATE: A Novel Ergonomic Upper-Limb Exoskeleton to Reduce Workers' Physical Strain

Data-Driven Ergonomic Risk Assessment of Complex Hand-intensive Manufacturing Processes

A Multi-disciplinary Assessments Tool for Human-Machine Interaction

An Online Multi-Index Approach to Human Ergonomics Assessment in the Workplace

Biomechanical Effects of Using a Passive Exoskeleton for the Upper Limb in Industrial Manufacturing Activities: A Pilot Study

Online Ergonomic Evaluation in Realistic Manual Material Handling Task: Proof of Concept

Using Digital Human Modelling to Evaluate the Risk of Musculoskeletal Injury for Workers in the Healthcare Industry

A Full-Chain OpenSim Model and Its Application on Posture Analysis of an Overhead Drilling Task

Development of an ergonomic wearable robotic device for assisting manual workers

A Novel Passive Occupational Shoulder Exoskeleton With Adjustable Peak Assistive Torque Angle For Overhead Tasks

Digitalization of Musculoskeletal Risk Assessment in a Robotic-Assisted Assembly Workstation

Human Factors in Digital Industrial Systems