Abstract:The aviation industry's efforts to reduce carbon emissions have driven the rapid development and scale-up of sustainable aviation fuels (SAFs). SAFs have the potential to significantly reduce CO 2 lifecycle emissions by up to 80% in comparison to Jet A and other conventional fossil-derived jet fuels. For multiple logistical and practical reasons, it is preferable to ensure that SAFs are 'essentially identical' (also referred to as 'drop-in SAF') to conventional jet fuel in terms of their performance, durability and compatibility with existing hardware systems. Because the majority of SAFs are not identical (non-drop-in) to conventional jet fuel, they have not been approved for use in their neat (100%) form. Instead, these non-identical SAFs are named synthetic blend components (SBC) as they are blended with conventional fuels to different extents per ASTM D7566-23a. It should be noted that there are on-going efforts to develop non-drop in SAF specifications to broaden their proliferation and maximise the aviation industries' ability to reduce CO 2 lifecycle emissions. One very important area of focus is the compatibility of SAFs with engine and fuel system seals, specifically understanding the dynamics of elastomeric seals. To address this, a novel approach has been developed to measure seal dynamics in flowing fuel. This technique has been applied to study the dynamic seal behaviour of four industrially relevant elastomer seals commonly employed in aviation fuel systems. The study involved three test fuels: (i) conventional fossil-derived Jet A, neat hydroprocessed esters and fatty acids (HEFA) SAF, and neat alcohol to jet (ATJ) SAF. Notably, both HEFA and ATJ fuels contain 0% aromatics, in contrast to Jet A, which typically contains around 17% aromatics by volume. The novel fuel-elastomer test rig used in this study was designed to simulate a practical scenario in which fuel flows through the inner surface of a pre-loaded static O-ring. The results of these tests demonstrate that the behaviour of different nitrile elastomers is unique to their formulation, and in all cases, the behaviour in HEFA and ATJ SAF differs significantly from that in Jet A. However, new fuel approval tests may only list one type of elastomer for evaluation, for example the 'Fit-for-Purpose' test in ASTM D4054-22 Tier 2 lists one specific nitrile. The findings of this study highlight the complexities of fuel-elastomer interactions within nominally identical chemical families and emphasise the potential risks of assessing compatibility based on tests conducted with a single member of a chemical family.

O-Rings Material Deterioration due to Contact with Biodiesel Blends in a Dynamic Fuel Flow

Elastomer-Based Sealing O-Rings and Their Compatibility with Methanol, Ethanol, and Hydrotreated Vegetable Oil for Fueling Internal Combustion Engines

Research on the Material Compatibility of Elastomer Sealing O-Rings

Study on Volume Swell and Mechanical Properties of Fuel System Elastomers with Fischer–Tropsch Fuel for Diesel Engines

Effect of engine oil dilution by waste ayurvedic oil biodiesel on tribological behavior of liner-ring tribo pair material

Reliability of renewable oxygenated fuels in engines: A comprehensive review of long-term testing

Compatibility Effects of Waste Cooking Oil Biodiesel Blend on Fuel System Elastomers in Compression Ignition Engines

An Experimental Study of Friction and Wear Characteristics of Sunflower and Soybean Oil Methyl Ester Under the Steady-State Conditions by the Four-Ball Wear Testing Machine

An investigation of the longevity wear assessment during the utilisation of biofuel-diesel blends in a diesel engine: a case study of crude palm and crude jatropha oil

Method of Evaluation of Materials Wear of Cylinder-Piston Group of Diesel Engines in the Biodiesel Fuel Environment

Additively Manufactured O-rings: Tensile Strength and Swelling Behavior in the Presence of Gasoline and Surrogate Mixtures

Effect of palm-sesame biodiesel fuels with alcoholic and nanoparticle additives on tribological characteristics of lubricating oil by four ball tribo-tester

Case Study of Biodiesel-Diesel Blends as a Fuel in Marine Environment

Elastomer compatibility study of oil-based and ester-based drilling fluids

Friction and wear properties of several rubber materials for high pressure O-ring

Interactions between Used Cooking Oil Biodiesel Blends and Elastomer Materials in the Diesel Engine

The Effects of Material Degradation on Sealing Performances of O-Rings

A performance degradation model of nitrile butadiene rubber (NBR) O-rings for hydrogen permeation effects under high-pressure

Investigation on elastomer behaviour when exposed to conventional and sustainable aviation fuels

Performance and Emission Analysis of Biodiesel Blends in a Low Heat Rejection Engine with an Antioxidant Additive: An Experimental Study

Extraction of biodiesel from pomelo peel and investigation of its efficiency as a lubricant in water-based drilling fluid