Abstract:Porous and composite piezoelectric ceramics are of interest for underwater ultrasonic transducers due to their improved voltage sensitivity and acoustic matching with water, compared with their dense counterparts. Commonly, these materials are fabricated by dice-and-fill of sintered blocks of polycrystalline piezoceramic, which results in a high volume of waste. The freeze-casting technique offers a low waste and scalable alternative to the dice-and-fill method to produce porous piezoceramics with highly orientated, anisometric pores. In this article, we have fabricated underwater ultrasonic transducers from freeze-cast lead zirconate titanate (PZT) with a range of porosities. The porous PZT samples were characterized in terms of their piezoelectric and dielectric properties before being encapsulated for acoustic performance testing in water. Off resonance, the on- axis receive sensitivity of the manufactured devices was approximately [Formula: see text]; the transmit voltage response (TVR) was in the range of approximately [Formula: see text] at 60 kHz to [Formula: see text] at 180 kHz. The most porous transducer devices (0.51, 0.43, and 0.33 pore fraction) exhibited primarily a thickness mode resonance, whereas the least porous transducers (0.29 pore fraction and dense benchmark) exhibited an undesired radial mode, which was observed as an additional resonant peak in the electrical impedance measurements and lateral off-axis lobes in the acoustic beampatterns. Our results show that the acoustic sensitivities and TVRs of the porous freeze-cast transducers are comparable to those of a dense pressed transducer. However, the freeze-cast transducers with porosity exceeding 0.30 pore fraction were shown to achieve an effective structure with aligned porosity that suppressed undesired radial mode resonances.

Characterization of High Porous PZT Piezoelectric Ceramics by different Techniques

Porous PZT Ceramics with High Hydrostatic Figure of Merit and Low Acoustic Impedance by TBA-Based Gel-Casting Process

Microstructure and Electrical Properties of Porous Pzt Ceramics Fabricated by Different Methods

Processing and properties of porous PZT ceramics from particle-stabilized foams via gel casting

Effects of Porosity on Dielectric and Piezoelectric Properties of Porous Lead Zirconate Titanate Ceramics

Fabrication of Porous PZT–PZN Piezoelectric Ceramics With High Hydrostatic Figure of Merits Using Camphene‐Based Freeze Casting

Processing of porous ceramics: Piezoelectric materials

Microstructure and Electrical Properties of Porous PZT Ceramics Derived from Different Pore-Forming Agents

Effects of Sintering Behavior on Piezoelectric Properties of Porous Pzt Ceramics

Piezoelectric properties of the 1-3 type porous lead zirconate titanate ceramics

Microstructure and electrical properties of porous PZT ceramics with unidirectional pore channel structure fabricated by freeze-casting

Porosity effect on the functional properties and energy harvesting performance of Ba0.85Ca0.15Ti0.90Zr0.10O3 ceramics

Effects of Foam Composition on the Microstructure and Piezoelectric Properties of Macroporous PZT Ceramics from Ultrastable Particle-Stabilized Foams

Enhanced Piezoelectric Property of Porous Lead Zirconate Titanate Ceramics with One Dimensional Ordered Pore Structure

Ultrasonic Transducers Made From Freeze-Cast Porous Piezoceramics

Effect of Porosity on Functional Properties of Lead-Free Piezoelectric BaZr0.15Ti0.85O3 Porous Ceramics

High piezoelectric sensitivity and hydrostatic figures of merit in unidirectional porous ferroelectric ceramics fabricated by freeze casting

Effects of Sintering Behavior on Microstructure and Piezoelectric Properties of Porous PZT Ceramics

Fabrication of porous PZT ceramics using micro-stereolithography technology

Effects of pore size and orientation on dielectric and piezoelectric properties of 1–3 type porous PZT ceramics

Porosity and Electrical Properties of Porous PZT 95/5 Ferroelectric Ceramics